Spud_J

Part No Description Rate N/mm Coils
43190 Revolution Spring Soft 1.8 11
41391 Revolution Spring Medium 1.9 10
41392 Revolution Spring Medium Hard 2.2 9
41393 Revolution Spring Hard 2.3 8
41382 Revolution Spring MR032 Inox Soft 3.8 9
41383 Revolution Spring MR032 Inox Hard 4.3 8
41386 Revolution Spring MR035 Inox Soft 5.2 10
41387 Revolution Spring MR035 Inox Hard 5.6 9

Hope that helps!

Steve

C_O_jones

iTrader: (11)

A BIG Thanks to Peter, Travis and Alex for all the help at the REEDY!!!!!!!!

Great bunch of racers, always ready to help.

Congrats TRAV!!!!!! Made it a 2 year SWEEP fo Br00d.

Fred

corallyman

iTrader: (101)

Pete,

You got a PM.


Trav,

Great job at the Reedy Race. One down one to go. Cali should be a good race between the Br00dies.

Steve

quantum

thanks, thats great.
only two of the MR springs are sold on the team brood website, the question is, which two?

John Tag

iTrader: (42)

Peter you got PM......

loopedeloop

Hi guys

Which of the following would be best for asphalt 12t limit touring on yoko BD.
track is small but open and pretty fast.

Checkpoint or cobalt?

I understand the checkpoints will wear brushes/comm less and have more torque.
Is this correct?

Thanks for your reply

peter_robinson

iTrader: (21)

loop - after the reedy race... i definately prefer the V2 over anything else.

here is my V2 setup from the race for all to try.

Team Br00d Mike Dumas edition 7x1
Sprint Brushes
MR Springs.32mm 9-coil 3.8 rate
Timing - 16 degrees
Final Drive Ratio - 8.57:1

the setup on Travis' motor was:

Reedy Handout quadmag
reedy 767 brushes
red springs on both the pos./neg.
Final Drive Ratio - 5.49:1

marzz23

Hey Guys,
here is some pictures of my 1/10th scale elec dirt oval car powered by team brood. Thought you all would like to see it, thanx for the support.

loopedeloop

Thanks peter, will be ordering a checkpoint I guess.
Do you have any gearing suggestions for 12x2 checkpoint? I assume
it will be slightly different to the cobalt which I currently run @ 7-7.3 FDR.

Thanks man

RocketRacer

i just got myself a Br00d V2 7x2 motor.

these are the specs on my car.

Tamiya TB Evolution IV MS
Novak GTX ESC
Nosram 4200 Factory Team Matched Packs
Jaco Foam tyres 63mm

how would you recommend i gear the car to run with the 7x2 motor? any tips and suggestions would be great it's my first team brood product!

PetterS

Order #1027....!?!?!??!!

peter_robinson

iTrader: (21)

gear it so it tops out just before you have to let off on the longest straight stretch.

PetterS

Is the V2 Mike Dumas edition available...?

TripleX-JT

iTrader: (1)

Peter or Eddie,
I sent a couple of emails ablout a month ago to info@teambr00d in regards to a new CO27 motor in which the armature split by one of the balance holes after about 3 min racing. Im just wondering what the status is of the email.

If you didnt get the email here is my question....Can I send the armature back for another? Since it was a brand new motor and I would think that it should last longer than 3 min. If not is it possible to purchase another? The rest of the motor is fine just the armature is shot.

Just let me know when you can

Thanks,

THeGame

They should be out soon but no date yet... Sorry..