MurfDogg Motor Works Discussion thread
#1186
I have been running a Murfdogg 17.5 in my SC10 for over a month now and love it! Good power. I qualified 4th and finished 8th in stock SC at Motorama. Indoor racing I have: 2 TQs, 3 1st place finishes, and 1 2nd place finish. All in Pro2. I can't wait to try a Murfdogg 13.5 outdoors. Keep up the good work Matt !!
Jarodd Goedel
www.CanalsideRacingProducts.com
Jarodd Goedel
www.CanalsideRacingProducts.com
#1187
Tech Elite
iTrader: (10)
Ok guys got another issue on my Murffdogg motor I had this motor for few months and run it the second time last weekend after the race I pulled the motor apart clean it and re-lube the bearing when I'm putting the screws back in 2 of them strips and it won't grab I don't know if the screws are short or what but I can't put the motor back together...
#1188
Motorama 2012 Results
Qualified 4th and finished 8th in the A main in 2wd Stock SC at Motorama 2012 using a Murfdogg 17.5. Keep up the great work Matt !
#1189
Jochim_18: Had this happen on a Blue can motor once and I used some epoxy on screw, reinstalled and worked fantastic. Would recommend sending Matt a 'pm' to determine a good course of action to take for permanent fix.
jdg_rit: That is awesome!!!! Cangrat's and keep up the great racing!!!
jdg_rit: That is awesome!!!! Cangrat's and keep up the great racing!!!
#1190
Hey guys I was wondering if there was any difference between these 2 black murfdogg 17.5 motors, I know they have different solder tabs but is there a difference in performance or anything? Does one benefit from the other?
http://www.tqrcracing.com/shop/produ....asp?p_id=1070
http://www.rctech.net/forum/attachme...rs-stealth.jpg
The second one I believe is the same as the original blue cans but just in black
Hopefully I can find this out as soon as possible, I tried searching but cant seem to find much.
Thank you!
http://www.tqrcracing.com/shop/produ....asp?p_id=1070
http://www.rctech.net/forum/attachme...rs-stealth.jpg
The second one I believe is the same as the original blue cans but just in black
Hopefully I can find this out as soon as possible, I tried searching but cant seem to find much.
Thank you!
#1192
#1194
Hey guys I was wondering if there was any difference between these 2 black murfdogg 17.5 motors, I know they have different solder tabs but is there a difference in performance or anything? Does one benefit from the other?
http://www.tqrcracing.com/shop/produ....asp?p_id=1070
http://www.rctech.net/forum/attachme...rs-stealth.jpg
The second one I believe is the same as the original blue cans but just in black
Hopefully I can find this out as soon as possible, I tried searching but cant seem to find much.
Thank you!
http://www.tqrcracing.com/shop/produ....asp?p_id=1070
http://www.rctech.net/forum/attachme...rs-stealth.jpg
The second one I believe is the same as the original blue cans but just in black
Hopefully I can find this out as soon as possible, I tried searching but cant seem to find much.
Thank you!
#1195
I use both versions. The one that says 1.1 (first link) is the newest version and have had great success with both. The 1.1 design seems to be structurally better and is the one I prefer to use.
#1196
Tech Apprentice
The 10.5t is an awesome motor that provides good speed, smooth delivery and easy to drive in 2WD Buggy. If you already have experience with 2WD Buggy, I would recommend a 8.5t. Initially if you have to get used to it, you can tame it down with esc programming and work up to its full potential later. You wouldn't be dissapointed with either choice.
Awesome! I'm looking to learn again...while I drive the buggy at 17.5 for a bit.
I was on the site earlier and had a hard time finding prices...
What does a 10.5 or 8.5 come in at?
#1197
#1198