Hyper TT 4wd 1/10th Truggy Thread
#3676
any of you guys know were i can get a 160mm long batt tray as i need one for my new batts to fit in the standard one is too short
#3677
#3678
i have for now but i was hoping not to as i dont want the battery to get damaged with it being exposed this is what it looks like now
Last edited by stuartd; 04-18-2012 at 03:10 PM.
#3679
#3680
Hey guys quick question, I just purchased a roller ofna and will be putting my castle SCT 3800kv combo in it, what pinion gear should I use? I think the truck came with the stock spur gear it's a blue color one. Oh and I will be running a gens ace 2s 5000 40c..I will be using the truck for bashing and ocassionaly track events
#3681
Hey guys quick question, I just purchased a roller ofna and will be putting my castle SCT 3800kv combo in it, what pinion gear should I use? I think the truck came with the stock spur gear it's a blue color one. Oh and I will be running a gens ace 2s 5000 40c..I will be using the truck for bashing and ocassionaly track events
3S and a 11T pinion. Temps are about 142F.
#3683
Tech Elite
iTrader: (71)
I would be careful about temps with the Castle SCT 3800KV combo for the motor. A friend of mine put one in his slash and used a 16T pinion and it would stop for a few minutes then go again. I called up Castle and can't remember if they said do not use more than a 15T or 14T pinion. I would start out with a 14T pinion. The latter information is for a 2S setup. I am using the Castle SCT 3800Kv in a Losi 810E and use
3S and a 11T pinion. Temps are about 142F.
3S and a 11T pinion. Temps are about 142F.
You can't compare gearing between models as they have different drive ratios, different weights, different wheel diameters, and different purposes. Heck even the number of cells will change what gearing you should shoot for.
#3684
I have a Hyper 10SC and was speaking of experience with the Castle 3800KV on an outdoor track. I would think that the Hyper 10Sc and the Hyper TT would have the same gearing as they are almost identical. Evidently, my latter post was confusing as I now use the Castle 3800KV in a Losi 810E.
#3685
So if I use a 12 pinion gear I would be fine then? Would it be atleast over 30mph with that setup on 2S?
#3686
Tech Regular
Gearing is the same on a hyper 10sc but a hyper tt is lighter so you can gear higher. I own both.
#3687
Ohh and I forgot to ask, I have a HobbyKing 120a esc and a Tacon 4420kV motor. I have it right now on my ecx ruckus, that thing flys on 2S. Do u guys think it would be overkill for the TT? If I use this setup what pinion har should I get?
#3688
Tech Elite
iTrader: (71)
I have a Hyper 10SC and was speaking of experience with the Castle 3800KV on an outdoor track. I would think that the Hyper 10Sc and the Hyper TT would have the same gearing as they are almost identical. Evidently, my latter post was confusing as I now use the Castle 3800KV in a Losi 810E.
As for the 120a esc...the hk 120 would be overkill and it would be a problem getting it to fit also (made the mistake of trying once before). The HK 100a esc works great and is of similiar size to MMP
#3689
Hey guys quick question, I just purchased a roller ofna and will be putting my castle SCT 3800kv combo in it, what pinion gear should I use? I think the truck came with the stock spur gear it's a blue color one. Oh and I will be running a gens ace 2s 5000 40c..I will be using the truck for bashing and ocassionaly track events
#3690