Losi 8ight building and setup
#7487
Tech Elite
iTrader: (8)
Na, out of the box the roller is pretty right. Don't know about the tracks over there, but over in oz our track starts off pretty tacky and then seems to go to nearly the blue groove status, so all I done was lowered the back shock oil by 5wt and the same with the front. But they are great just out the box
#7488
Tech Master
iTrader: (11)
You can run without the small shims that they show b/w the spacer and b/w the bearing and clutch nut if you need to. I had to take them all out b/c the bell wouldn't spin freely with any of the small shims in. About 3/4 gallon through, I pulled the clutch and the bearings looks fine.
#7490
Tech Master
iTrader: (3)
Okay, it's a tight fit but it is working. My ignitor died during the break-in idle. Engine kept stalling, so I was leaning it out and re-starting, and finally the bitch wouldn't start again. At first I thought the plug was gone, but I tried the ignitor on other plugs and it was a no-go.
Anyway, kind of off-topic, but should I be worried about temps of 220-240 when just idling on the box? That's what she's giving me.
Anyway, kind of off-topic, but should I be worried about temps of 220-240 when just idling on the box? That's what she's giving me.
#7491
Anothe silly question, looking over the build papers, often times I see a little aerosol spray can picture, sometimes right next to the loctite.
Does it mean spray with compressed air? lube? sorry !!
thank you.
Does it mean spray with compressed air? lube? sorry !!
thank you.
#7492
Tech Master
iTrader: (11)
Not sure what you mean by a tight fit, but that clutch bell needs to spin freely. Asking how to break in an engine is like asking which engine is best, you're going to get a lot of different answers. But, I wouldn't want mine at 220 or more on the box, I'd richen it. I run 1 tank though mine at about 1 minute intervals on the box, usually temping about 175.
The aerosol can pic means to clean the part before you apply Loctite. Look in the back of the manual in the hardware section, at the bottom there's a legend for the symbols.
The aerosol can pic means to clean the part before you apply Loctite. Look in the back of the manual in the hardware section, at the bottom there's a legend for the symbols.
#7493
well darn, there it is, right next to the setup sheets, didn't even look there.
Thank you my man!
Thank you my man!
#7494
The best shoes I have found are the Dynamite Max-Life shoes. I had one set last right at 3 gallons and they still had life left in them. They need hardly any maintenance as well. I would look them over at every clutch bell bearing change and clean them up and that's it..........
#7495
i had a some bad experiences with the Dynamite shoes and All silver's not lasting more then a week or 2.....they work for some but NOT all.
#7498
Tech Regular
iTrader: (5)
It also depends on Motors, tuning, trigger finger control, track surface, etc. You can't tell me that a Go-Tech Sport 3 port motor will have the same effect on clutch shoes as a CEO-Modded NovaRossi. I've heard the same thing from different guys here - some love the Dynamite shoes, some only use the Losi Long-wears, some only use Losi Lightweights. There are too many other factors in place to say "these shoes suck compared to ___." On one motor, possibly - on the next guys', that might not be the case.
If you're looking for longevity out of a clutch, try what Donny (cornerspeed) posted a few pages back - all composites with gold springs, and a new (non-used) clutch bell. As he said, 4 composite shoes will definitely last longer than any alum/composite combo, as there is no aluminum flying around in there chewing up the plastic shoes. In theory, it should be easier on bearings too, just keep the bearings clean of the plastic dust. And make sure to use a brand new clutchbell.
If you're looking for longevity out of a clutch, try what Donny (cornerspeed) posted a few pages back - all composites with gold springs, and a new (non-used) clutch bell. As he said, 4 composite shoes will definitely last longer than any alum/composite combo, as there is no aluminum flying around in there chewing up the plastic shoes. In theory, it should be easier on bearings too, just keep the bearings clean of the plastic dust. And make sure to use a brand new clutchbell.
#7499
Tech Addict
iTrader: (19)
Na, out of the box the roller is pretty right. Don't know about the tracks over there, but over in oz our track starts off pretty tacky and then seems to go to nearly the blue groove status, so all I done was lowered the back shock oil by 5wt and the same with the front. But they are great just out the box
Got to get down your way for some killer snapper fishing
#7500
Tech Master
iTrader: (11)
It also depends on Motors, tuning, trigger finger control, track surface, etc. You can't tell me that a Go-Tech Sport 3 port motor will have the same effect on clutch shoes as a CEO-Modded NovaRossi. I've heard the same thing from different guys here - some love the Dynamite shoes, some only use the Losi Long-wears, some only use Losi Lightweights. There are too many other factors in place to say "these shoes suck compared to ___." On one motor, possibly - on the next guys', that might not be the case.
If you're looking for longevity out of a clutch, try what Donny (cornerspeed) posted a few pages back - all composites with gold springs, and a new (non-used) clutch bell. As he said, 4 composite shoes will definitely last longer than any alum/composite combo, as there is no aluminum flying around in there chewing up the plastic shoes. In theory, it should be easier on bearings too, just keep the bearings clean of the plastic dust. And make sure to use a brand new clutchbell.
If you're looking for longevity out of a clutch, try what Donny (cornerspeed) posted a few pages back - all composites with gold springs, and a new (non-used) clutch bell. As he said, 4 composite shoes will definitely last longer than any alum/composite combo, as there is no aluminum flying around in there chewing up the plastic shoes. In theory, it should be easier on bearings too, just keep the bearings clean of the plastic dust. And make sure to use a brand new clutchbell.