1LikesOFNA LD3 pro
03-01-2004, 07:37 PM
#871
Hello,guys
Is there any difference in performance between the ofna dual chamber pipe and the RDlogics tc3 pipe
they look very similar,i think the ofna pipe is a bit longer,who has made the test?????????
Is there any difference in performance between the ofna dual chamber pipe and the RDlogics tc3 pipe
they look very similar,i think the ofna pipe is a bit longer,who has made the test?????????
03-01-2004, 07:46 PM
#872
Tech Master
The Hong Nor pipe (or "OFNA" for you ppl in America 
) is long, too long, I found I was leaning out engines to get them to rev 
. I now have the THS Pipe, it looks like the RD Logic pipe but stinger is different otherwise looks like a twin. I like it much better 
) is long, too long, I found I was leaning out engines to get them to rev . I now have the THS Pipe, it looks like the RD Logic pipe but stinger is different otherwise looks like a twin. I like it much better
03-01-2004, 07:56 PM
#873
Ok...couple questions...
1) DTM or anyone that has the Champ Ed or the Aluminum steering set up on their car...I am currently assembling my Champ...Ive built my steering and I seem to have a lot of play...it almost seems as if the "tubes" that go through the bearings are slightly too small and the whole assembly rocks around quite a bit.I also can not tighten the screws totally, without the bearings binding.I have tried to install washers in several different areas, but it doesnt help any.Is this normal or have I done something wrong?
2) Tire truers....Im assuming, being I'll likely be running foams, that one would be necessary.Any suggestions????
1) DTM or anyone that has the Champ Ed or the Aluminum steering set up on their car...I am currently assembling my Champ...Ive built my steering and I seem to have a lot of play...it almost seems as if the "tubes" that go through the bearings are slightly too small and the whole assembly rocks around quite a bit.I also can not tighten the screws totally, without the bearings binding.I have tried to install washers in several different areas, but it doesnt help any.Is this normal or have I done something wrong?
2) Tire truers....Im assuming, being I'll likely be running foams, that one would be necessary.Any suggestions????
03-01-2004, 07:56 PM
#874
THS=RDLogic
03-01-2004, 08:42 PM
#875
Tech Master
THS$ < RDLOGIC$
03-01-2004, 08:44 PM
#876
Originally posted by au_Nightmare
THS$ < RDLOGIC$
THS$ < RDLOGIC$
; 
03-01-2004, 09:56 PM
#877
where can i aqquire a THS LD3 pipe from?
03-01-2004, 10:11 PM
#878
Tech Master
Throw an email to your friendly HK shop and I am sure they can help 
Photo of THS pipe and stock LD3 Pro pipe behind it..
Photo of THS pipe and stock LD3 Pro pipe behind it..
03-02-2004, 01:37 AM
#879
Tech Rookie
LD3 diff
Just built my champ edition and very nice it is too , does anyone know if a front 6 gear diff can be purchased complete? if so a part number?
also which is the best place to get stuff shipped to the uk.
also which is the best place to get stuff shipped to the uk.
03-02-2004, 11:07 AM
#881
Re: LD3 diff
Originally posted by Barney Rubble
Just built my champ edition and very nice it is too , does anyone know if a front 6 gear diff can be purchased complete? if so a part number?
also which is the best place to get stuff shipped to the uk.
Just built my champ edition and very nice it is too , does anyone know if a front 6 gear diff can be purchased complete? if so a part number?
also which is the best place to get stuff shipped to the uk.
03-02-2004, 02:52 PM
#883
03-04-2004, 02:19 PM
#885
Tech Master
I seen that header also and had same thoughts.. just go the THS Pipe