759LikesMugen MTC1
03-13-2018, 09:34 AM - Wikipost
|
|||
|
|||
|
Mugen MTC1 Wiki:
MTC1 Manual on the Mugen Web Site. Correction for the manual   The max/min tooth count of the spur and pinion combined. 64p = 127 to 164 total teeth  48p = 95 to 120 total teeth  People who have spare spur gears left over from other cars which they wish to use but can only utilize 2 of the 4 mounting holes, here's neat trick from MKAH to drill 2 more holes precisely in the spur gear: 1.Dismantle the Spur Holder and mount XRAY Spur with two screws.  2.If you have take a 3mm Top Setting Screw  3.Get the Top Screw in the first free thread to the Spur Holder from the other side until it touches the Spur a litle bit. Make the same with the second free Thread.  4.Dismantle Top set Srew an the two screws witch holds the Spur on the Holder. Now you see two marks absolutely central.  5. Take an 3mm Driller an Drill the holes at the marked places  6.Mount the Spur with the two old and two new holes on the Spur.  Spur Gears known to fit the gear holder with the correct hole pattern 1. Axon 2. Panaracer Upper front arm hinge pin set screw tip (or any of the kit set screws): When installing the set screw run the set screw in until you can see it come into the hinge pin gap. Back the screw out and make sure there is no flashing in the way and then the screw. Now slide the pin in and you should hit the pin and come to a dead stop. It will be a solid feel and not sloppy like it will not tighten which is caused by any loose plastic. Hara's Setup  Robert Pietsch's Latest Carpet Setup 
|
08-08-2019, 04:34 AM
#1576
Where i can find belt low fiction?
08-08-2019, 05:00 AM
#1577
08-08-2019, 07:10 AM
#1578
Tech Apprentice
With the old front upper arms, I think alloy frame (the Mugen one, not aftermarket products) is kind of mandatory on high grip surfaces.
With the performance kit, maybe you can try the carbon chassis.
08-08-2019, 08:02 AM
#1579
08-08-2019, 10:26 AM
#1580
08-19-2019, 05:37 AM
#1582
Can someone please confirm the correct thickness for shock 4 hole part? While building I discovered that 3 are 2 mm thick and 1 is 1.5mm thicknesss. 1.5 moves freely and 2mm is very tight.
08-19-2019, 11:52 AM
#1583
The thicker 3 are correct - the E-Clip is supposed to be recessed into the piston head.
08-20-2019, 07:39 AM
#1584
Thanks David
09-15-2019, 07:56 AM
#1585
Need advice. Ordering this kit next week and I never ran a on road car. HT is putting together a black carpet track and asking what I’m going to need as far as setup, tools and tires. Know I’m gonna need a ride height gauge but is that it as far as tools? I plan on running Hobbywing esc but a stock motor is open to what ever. 17.5 is stock, right? These guys run parking lot and now they’re coming indoor and I’m not sure what they now about carpet and I def know they never seen a Mugen TC before. What’s a good tire for black carpet? Thinking I’ll need spare arms and maybe body posts. Not looking for tons of hopups because I’m not sure how far I want to take this until I figure it out first. Maybe get a aluminum chassis later cuz I would think that would be better for high grip. I’ll go with a bittydesign body cuz I love their 1/8 buggy bodies.
09-15-2019, 08:11 AM
#1586
Need advice. Ordering this kit next week and I never ran a on road car. HT is putting together a black carpet track and asking what I知 going to need as far as setup, tools and tires. Know I知 gonna need a ride height gauge but is that it as far as tools? I plan on running Hobbywing esc but a stock motor is open to what ever. 17.5 is stock, right? These guys run parking lot and now they池e coming indoor and I知 not sure what they now about carpet and I def know they never seen a Mugen TC before. What痴 a good tire for black carpet? Thinking I値l need spare arms and maybe body posts. Not looking for tons of hopups because I知 not sure how far I want to take this until I figure it out first. Maybe get a aluminum chassis later cuz I would think that would be better for high grip. I値l go with a bittydesign body cuz I love their 1/8 buggy bodies.
09-19-2019, 08:59 AM
#1587
Hallo this is my question
I have put gear spur 90 t but the spur touch on the chassis is possible?which is the maximum spur I can put in my mtc1?
I have put gear spur 90 t but the spur touch on the chassis is possible?which is the maximum spur I can put in my mtc1?
09-19-2019, 09:08 AM
#1588
09-19-2019, 09:17 AM
#1589
Tech Initiate
09-20-2019, 12:12 AM
#1590