Xray T4 '13
#3481
I knew it! LOL
#3484
Tech Regular
If loosening off all screws including the shock tower screws, top deck and bulkhead screws does not sort it then I would agree with defcone and check the bulkheads to see if they are bent. The only way I have been able to do this in the past was to strip the car down and put each piece of alloy on a flat glass surface and see if it's bent. I have not had this happen with the Xray but did have it happen once with a TC6.
As a side note, when you are tightening up the screws I have found it useful to have a long iron bar that I put across the two shock towers and push down while I tighten each of the top deck screws.
As a side note, when you are tightening up the screws I have found it useful to have a long iron bar that I put across the two shock towers and push down while I tighten each of the top deck screws.
#3485
#3487
Tech Apprentice
tweak
also when the you have the chassis sitting flat press your thumb down in the centre of the shock tower and undo the four screws then re-tighten.
make sure that screws on the chassis are sitting flush.
#3489
hello everyone! well finally since nationals i have had time to look at my car and write the setup down that i won with in 13.5 touring . i ran the same car in 17.5 so it will work good with class also . i wound up finishing 5th overall in 17.5 because of bad luck in the mains . anyway here is the link to the setup (http://forum.teamxray.com/xform/inde...D=365&setup=t4)
if you have any questions just ask
thanks
Cory Parsons
if you have any questions just ask
thanks
Cory Parsons
#3490
Tech Elite
iTrader: (72)
I'm sure this has been answered but I'm not finding it. I want to purchase spare rear arms but the kit part # shows 303163 yet it shows 3 sway bar mounts. However it only has a 2 sway bar mounts according to my part # lookup. The arms I have are the Hard arm and I "think" the P/N is 303167. My question is, is 303167 in fact the Hard arm or is this a different material and is this in fact the kit rear arm?
Thanks
Thanks
#3491
I'm sure this has been answered but I'm not finding it. I want to purchase spare rear arms but the kit part # shows 303163 yet it shows 3 sway bar mounts. However it only has a 2 sway bar mounts according to my part # lookup. The arms I have are the Hard arm and I "think" the P/N is 303167. My question is, is 303167 in fact the Hard arm or is this a different material and is this in fact the kit rear arm?
Thanks
Thanks
Skiddins
#3492
Tech Fanatic
iTrader: (52)
Question about the anti-roll bar. No matter what I do to the mounting set screws or adjusting the set screws by the end of the bar, left and right just have uneven reaction. All arms go up&down freely. However, when lift up left, right will come up; but life up right, left only moves a little (shocks off).
Front 1.4 and rear 1.2 bar, similar case. How do I fix it? thanks!
Front 1.4 and rear 1.2 bar, similar case. How do I fix it? thanks!
#3494
Question about the anti-roll bar. No matter what I do to the mounting set screws or adjusting the set screws by the end of the bar, left and right just have uneven reaction. All arms go up&down freely. However, when lift up left, right will come up; but life up right, left only moves a little (shocks off).
Front 1.4 and rear 1.2 bar, similar case. How do I fix it? thanks!
Front 1.4 and rear 1.2 bar, similar case. How do I fix it? thanks!
#3495
Tech Master
iTrader: (22)
Join Date: Aug 2003
Location: Where there's smoke there's a tyre
Posts: 1,784
Trader Rating: 22 (100%+)
The tiniest tweak in the bar can throw it out alot on the car.