Official AE RC18 Thread!
#31
A couple more pics and a very short video - (3-4 seconds) - one of my RC18's buzzing the camera at 60+ mph. The car in the video is powered by a Mamba ESC, Dynamite C4-9200kv motor and 3 cell 1320mah Thunder Power Lipo's = Motor is turning at over 102,000 rpm at full throttle - Losi pre-glued foams on all 4.
Click here for video...
Enjoy...
Click here for video...
Enjoy...
#32
Originally Posted by needrcspeed
A couple more pics and a very short video - (3-4 seconds) - one of my RC18's buzzing the camera at 60+ mph. The car in the video is powered by a Mamba ESC, Dynamite C4-9200kv motor and 3 cell 1320mah Thunder Power Lipo's = Motor is turning at over 102,000 rpm at full throttle - Losi pre-glued foams on all 4.
Click here for video...
Enjoy...
Click here for video...
Enjoy...
#34
Looks good, sporting crime fighters for the half 8?
#36
Tech Fanatic
iTrader: (28)
Originally Posted by crabboy
Hi guys,
Heres a pic of my 100% real rc18 truggy it started as an 18b and was converted to a truck just as what happens in the 8th scale world
Heres a pic of my 100% real rc18 truggy it started as an 18b and was converted to a truck just as what happens in the 8th scale world
That looks sweet, yet another top ride by crabboy, Is that a brushless that I can spy in that there ??? Now I really want one of those too .. Go the Truggy.
P.s. The M18 is going great guns, I threw in my mamba and wow sticks like it is on rails... Thanks again man.
#37
loosk sweet so are the pro line rims for the half eight as well, i wanna do a buggy version with the jconcepts body and crimefighter.
did it take any modifiying or did the rims just bolt on
did it take any modifiying or did the rims just bolt on
#38
Tech Elite
iTrader: (58)
Originally Posted by thachowman
That looks sweet, yet another top ride by crabboy, Is that a brushless that I can spy in that there ??? Now I really want one of those too .. Go the Truggy.
P.s. The M18 is going great guns, I threw in my mamba and wow sticks like it is on rails... Thanks again man.
P.s. The M18 is going great guns, I threw in my mamba and wow sticks like it is on rails... Thanks again man.
Yep its a mamba system Glad your happy with the m18 it was always good to me but you sound like your getting a bit more use out of it
#39
Tech Elite
iTrader: (58)
Originally Posted by Rocket42
loosk sweet so are the pro line rims for the half eight as well, i wanna do a buggy version with the jconcepts body and crimefighter.
did it take any modifiying or did the rims just bolt on
did it take any modifiying or did the rims just bolt on
#40
Tech Initiate
Crabboy,
Nice car wish mine looked that good
Nice car wish mine looked that good
#41
Originally Posted by waltuo
Has anyone found a stronger servo saver for the 18T?
If you want the best steering this is the way to go
THese servos are ran in 1/12ths and they cost $95 new $40 used
best setup you can have
1.61 oz.
0.58" x 1.30" x 1.02"
38 oz [email protected]
0.11 [email protected]
Coreless Motor
Nylon Gears
#42
well my crimefighter tires and rims got here fo my rc18b, the tires are as wide as the buggy fronts. the rims are bigger dia. then assoc. rims and with the tires mounted they are just slightly taller than the stock ae tires. i can't wait till i get the hex adapters (waiting for the shipment from hk) the tires should last much longer than the stock ones. when i get the adapters i will post how much the width gets changed with these new rims.
#43
Integy EVO
Hii..
Has Anyone has experience with Integy EVO-X Conversion?
it looks nice to me.. but not so sure.
comment please..
Thank You
Has Anyone has experience with Integy EVO-X Conversion?
it looks nice to me.. but not so sure.
comment please..
Thank You
#45
if you can get it to fit in a 18b there is no reason why you could use the qc2, voltage is the same and amp draw is less. so the speedo would just run cooler.