Bittydesign 1/10 TC 190mm bodyshells!
#526
which is what i need. just hoping the car doesnt become too lazy
#527
Regional Moderator
iTrader: (1)
I just got the JP8 and was test fitting it on the car. I had to do a triple take on the label to make sure its 190mm and checked the width with the ruler to make sure it is in fact 190mm. The body looks so much wider than others. Theres a good 1cm gap between the front wheel and the body. I dont remember bodies for other manufactures being this wide for a 190mm car.
#528
Super Moderator
iTrader: (239)
I just got the JP8 and was test fitting it on the car. I had to do a triple take on the label to make sure its 190mm and checked the width with the ruler to make sure it is in fact 190mm. The body looks so much wider than others. Theres a good 1cm gap between the front wheel and the body. I dont remember bodies for other manufactures being this wide for a 190mm car.
#529
I just got the JP8 and was test fitting it on the car. I had to do a triple take on the label to make sure its 190mm and checked the width with the ruler to make sure it is in fact 190mm. The body looks so much wider than others. Theres a good 1cm gap between the front wheel and the body. I dont remember bodies for other manufactures being this wide for a 190mm car.
#530
Regional Moderator
iTrader: (1)
Yeah Im planning on running this body on the Gizmo Beta, cant wait to test it out.
Which line do you trim the body to? Im guessing everyone will slam the body as close to the ground as possible right?
I didnt notice the wing difference, but with such a wide car it should have a wider wing as well.
Which line do you trim the body to? Im guessing everyone will slam the body as close to the ground as possible right?
#531
Yeah Im planning on running this body on the Gizmo Beta, cant wait to test it out.
Which line do you trim the body to? Im guessing everyone will slam the body as close to the ground as possible right?
I didnt notice the wing difference, but with such a wide car it should have a wider wing as well.
Which line do you trim the body to? Im guessing everyone will slam the body as close to the ground as possible right?
I didnt notice the wing difference, but with such a wide car it should have a wider wing as well.
#532
Super Moderator
iTrader: (239)
Yeah Im planning on running this body on the Gizmo Beta, cant wait to test it out.
Which line do you trim the body to? Im guessing everyone will slam the body as close to the ground as possible right?
I didnt notice the wing difference, but with such a wide car it should have a wider wing as well.
Which line do you trim the body to? Im guessing everyone will slam the body as close to the ground as possible right?
I didnt notice the wing difference, but with such a wide car it should have a wider wing as well.
#533
Our JP8 body shell measure 194mm wide so it's in line with others manufactures who make bodies at 192-193mm wide; the correct trim is the upper line marked on the front splitter and side skirts, follow this line and after cutting place the body at about 8-9mm height from the ground, this is the perfect setting of the body. We recommend to mount the body forwarded about 8mm, use the lines reported in the centre of the front wheel arch, the longer line is "neutral" position. The JP8 it comes with max whidth wing, if you need more rotation because you feel it's to planted on the back, reduce the wing to 18mm height and mount it more forward on the body.
#534
Yes also the M410 need a forward placement to reach the best performance, also in this case use the lines reported in the front whell arch.
#536
gripworksrc.com sells Bitty stuff! Quick shipping too
#537
#538
💥 It's finally here!!
The new JP8 ULT body shell offers addition specific improvements in handling and agility!
• The Ultra Lite Technology creating a ultra light body with maintained form during the run gives you that extra edge you need in competition.
• Less body roll and thus more cornerspeed to give you that extra performance.
Discover all the features about the ULT body at 👉bittydesign.net/en/jp8-ult
JP8 ULT by Bittydesign Co.
The new JP8 ULT body shell offers addition specific improvements in handling and agility!
• The Ultra Lite Technology creating a ultra light body with maintained form during the run gives you that extra edge you need in competition.
• Less body roll and thus more cornerspeed to give you that extra performance.
Discover all the features about the ULT body at 👉bittydesign.net/en/jp8-ult
JP8 ULT by Bittydesign Co.
#540
Can't seem to find pre-cut M410 bodies, did Bittydesign stop making them?