Ko Propo VFS-1 ESC
#256
Hugo
Hope to meet you there. Will send you PM before that race, if I donīt forget. What car will you be running there?
Hope to meet you there. Will send you PM before that race, if I donīt forget. What car will you be running there?
#257
I hope I'll meet you there, I'll be running the 415!
PM me if you have a good setup for this track cause i never went there.
Bye
PM me if you have a good setup for this track cause i never went there.
Bye
#258
Donīt know exactly yet, Iīm running the 415 or maybe the old and proven EVO III there. I donīt have any special setup Iīm running similar setup usually. Just the handout tires are different but I donīt know what they will use this year.
Maybe will be just the 2. nd race with the 415.
Maybe will be just the 2. nd race with the 415.
#259
Tech Master
iTrader: (14)
HarshGuy:
Hi,
Thanks that is what I was looking for. nice site BTW.
Hebiki:
Hi,
Also thanks. I was going to just set throttle hi point at 100. I will reset it to 150.
Where is a good place to buy a handheld adaptor from??? I don't get alot of screen time do to work. so again any help would be great. or any info on the laptop adaptor (hoping it is on a CD)
Thanks
Hi,
Thanks that is what I was looking for. nice site BTW.
Hebiki:
Hi,
Also thanks. I was going to just set throttle hi point at 100. I will reset it to 150.
Where is a good place to buy a handheld adaptor from??? I don't get alot of screen time do to work. so again any help would be great. or any info on the laptop adaptor (hoping it is on a CD)
Thanks
#260
What do you look for when programing the frequency?
Does running a high final frequency improve top speed?
Is there a limit to how low you can set the frequency before you put the esc at risk?
Looking at 27 turn stock programing, but any advice information, insight or reasoning would be helpful.
Does running a high final frequency improve top speed?
Is there a limit to how low you can set the frequency before you put the esc at risk?
Looking at 27 turn stock programing, but any advice information, insight or reasoning would be helpful.
#261
Your questions....
Originally posted by Tom
What do you look for when programing the frequency?
Does running a high final frequency improve top speed?
Is there a limit to how low you can set the frequency before you put the esc at risk?
Looking at 27 turn stock programing, but any advice information, insight or reasoning would be helpful.
What do you look for when programing the frequency?
Does running a high final frequency improve top speed?
Is there a limit to how low you can set the frequency before you put the esc at risk?
Looking at 27 turn stock programing, but any advice information, insight or reasoning would be helpful.
YGPM
#262
Originally posted by TimXLB
Where is a good place to buy a handheld adaptor from??? I don't get alot of screen time do to work. so again any help would be great. or any info on the laptop adaptor (hoping it is on a CD)
Thanks
Where is a good place to buy a handheld adaptor from??? I don't get alot of screen time do to work. so again any help would be great. or any info on the laptop adaptor (hoping it is on a CD)
Thanks
as for the PC interface, they're available at the Ko Propo site on shopatron
#263
Tech Elite
iTrader: (6)
Originally posted by TimXLB
HarshGuy:
Where is a good place to buy a handheld adaptor from??? I don't get alot of screen time do to work. so again any help would be great. or any info on the laptop adaptor (hoping it is on a CD)
Thanks
HarshGuy:
Where is a good place to buy a handheld adaptor from??? I don't get alot of screen time do to work. so again any help would be great. or any info on the laptop adaptor (hoping it is on a CD)
Thanks
#265
hey ko staff i noticed on the vfs 2000 you had to add on a couple of big capacitors which took alot of room on the car is this the case with the vfs-1?
#266
Tech Initiate
Actual Freq. and Freq. No. Cross Reference
Hi KO Staff,
I have bought the VFS-1 yesterday and is still studying all the manuals including the setting card, the setting adaptor and some of the sample setting sheets from both KO USA and Japan website. During my study, I find out that the relationship between the actual frequency and the frequency no. in the setup sheet is not linear. The difference is listed below. Could you lead me to the documentation of the cross reference of the actual freq. and freq. no.
Freq. (No.) Difference
1.31 (10) - 0.93 (1) 0.38
2.03 (20) - 1.31 (10) 0.72
3.12(30) - 2.03(20) 1.09
4.57 (40) - 3.12 (30) 1.45
7.14 (50) - 4.57 (40) 2.57
9.98 (60) - 7.14 (50) 2.84
May I also have your enlightenment on this setting such as the reason why and the benefits gained.
Just want to learn more. Thanks in advance.
Regards,
Kenny
I have bought the VFS-1 yesterday and is still studying all the manuals including the setting card, the setting adaptor and some of the sample setting sheets from both KO USA and Japan website. During my study, I find out that the relationship between the actual frequency and the frequency no. in the setup sheet is not linear. The difference is listed below. Could you lead me to the documentation of the cross reference of the actual freq. and freq. no.
Freq. (No.) Difference
1.31 (10) - 0.93 (1) 0.38
2.03 (20) - 1.31 (10) 0.72
3.12(30) - 2.03(20) 1.09
4.57 (40) - 3.12 (30) 1.45
7.14 (50) - 4.57 (40) 2.57
9.98 (60) - 7.14 (50) 2.84
May I also have your enlightenment on this setting such as the reason why and the benefits gained.
Just want to learn more. Thanks in advance.
Regards,
Kenny
#267
Originally posted by ngo8
hey ko staff i noticed on the vfs 2000 you had to add on a couple of big capacitors which took alot of room on the car is this the case with the vfs-1?
hey ko staff i noticed on the vfs 2000 you had to add on a couple of big capacitors which took alot of room on the car is this the case with the vfs-1?
No, this is not the case with the VFS-1 Pro. The new speedo is very nice. You only need the one short capacitor and the one new and improved schottky diode, and that is it.
-Mike
#268
wicked thats the only reason why i dont have now i have to try it .
#269
Tech Initiate
Re: Actual Freq. and Freq. No. Cross Reference
Originally posted by kennykay
Hi KO Staff,
I have bought the VFS-1 yesterday and is still studying all the manuals including the setting card, the setting adaptor and some of the sample setting sheets from both KO USA and Japan website. During my study, I find out that the relationship between the actual frequency and the frequency no. in the setup sheet is not linear. The difference is listed below. Could you lead me to the documentation of the cross reference of the actual freq. and freq. no.
Freq. (No.) Difference
1.31 (10) - 0.93 (1) 0.38
2.03 (20) - 1.31 (10) 0.72
3.12(30) - 2.03(20) 1.09
4.57 (40) - 3.12 (30) 1.45
7.14 (50) - 4.57 (40) 2.57
9.98 (60) - 7.14 (50) 2.84
May I also have your enlightenment on this setting such as the reason why and the benefits gained.
Just want to learn more. Thanks in advance.
Regards,
Kenny
Hi KO Staff,
I have bought the VFS-1 yesterday and is still studying all the manuals including the setting card, the setting adaptor and some of the sample setting sheets from both KO USA and Japan website. During my study, I find out that the relationship between the actual frequency and the frequency no. in the setup sheet is not linear. The difference is listed below. Could you lead me to the documentation of the cross reference of the actual freq. and freq. no.
Freq. (No.) Difference
1.31 (10) - 0.93 (1) 0.38
2.03 (20) - 1.31 (10) 0.72
3.12(30) - 2.03(20) 1.09
4.57 (40) - 3.12 (30) 1.45
7.14 (50) - 4.57 (40) 2.57
9.98 (60) - 7.14 (50) 2.84
May I also have your enlightenment on this setting such as the reason why and the benefits gained.
Just want to learn more. Thanks in advance.
Regards,
Kenny
May be I am not writing the exact name so that you do not give me any response on my question. A little bit disappointed.
For the documentation on cross reference between the frequency no. and the acutal frequency, I have already figured it out by copying them from the setting adaptor. What a painful job to copy 64 readings (pressing the button on the adaptor and jotting down the figures)
For the enlightenment on the frequency curve, it may be your commercial decision that it could not be shared. In that sense, I think it is understandable.
For those who are using the VFS-1, you can find below each frequency no. against actual frequency. Happy to share.
Freq. No Actual Freq. (in kHz)
1 - 0.93
2 - 0.97
3 - 1.00
4 - 1.03
5 - 1.07
6 - 1.11
7 - 1.16
8 - 1.20
9 - 1.25
10 - 1.31
11 - 1.37
12 - 1.45
13 - 1.52
14 - 1.61
15 - 1.70
16 - 1.80
17 - 1.85
18 - 1.92
19 - 1.98
20 - 2.03
21 - 2.10
22 - 2.19
23 - 2.28
24 - 2.37
25 - 2.47
26 - 2.58
27 - 2.70
28 - 2.81
29 - 2.96
30 - 3.12
31 - 3.29
32 - 3.45
33 - 3.62
34 - 3.73
35 - 3.86
36 - 3.98
37 - 4.14
38 - 4.27
39 - 4.42
40 - 4.57
41 - 4.80
42 - 4.97
43 - 5.20
44 - 5.41
45 - 5.71
46 - 5.96
47 - 6.30
48 - 6.63
49 - 6.93
50 - 7.14
51 - 7.28
52 - 7.51
53 - 7.85
54 - 8.07
55 - 8.34
56 - 8.68
57 - 8.98
58 - 9.35
59 - 9.60
60 - 9.98
61 - 10.60
62 - 10.88
63 - 11.45
64 - 12.00
#270
Kenny, Robert might be out on a business trip and that's why he has not responded. I am sure he will answer as soon as he sees your post.