Serpent S411
#1381
Tech Fanatic
iTrader: (12)
i also asked the same question from rcmarket, the best spurs if your running stock and they have all the sizes from 60-90 48p are the RW spur gears they are not off set like the xray ones and there is plenty of room for meshing and not running close to the belt i have been useining these and they are great RW spur gears
if possible (and its okay to ask) can you point me in the direction of someone who stocks the RW 48p spur gears, have been looking and cannot find any under 64tooth
cheers
#1382
#1383
#1384
Tech Elite
iTrader: (10)
www.rwracing.co.uk
[email protected]
hope this helps
#1386
Tech Fanatic
iTrader: (12)
Thanks for your help with the spur gears, really appreciate it
#1388
New to the serpent S411 club
Just pressed order on one of these (latest release with 2.25mm chassis) and I'm looking forward to try it out. At the same time I ordered the regular spare parts and a extra gear diff for the front.
Are there any other must have option parts I should fit when building the car, or is it OK right out op the box? I will be running indoor carpet.
Are there any other must have option parts I should fit when building the car, or is it OK right out op the box? I will be running indoor carpet.
#1389
Tech Elite
iTrader: (19)
Just pressed order on one of these (latest release with 2.25mm chassis) and I'm looking forward to try it out. At the same time I ordered the regular spare parts and a extra gear diff for the front.
Are there any other must have option parts I should fit when building the car, or is it OK right out op the box? I will be running indoor carpet.
Are there any other must have option parts I should fit when building the car, or is it OK right out op the box? I will be running indoor carpet.
#1390
If I understand you correctly then it should be like below:
FF: 3.0
FR: 2.0
RF: 0.0
RR: 3.5
Can you please explain with a few words the reasoning for these changes?
Does anyone else have an opinion on this?
I bought the spring sets so I should be OK there. What about the sway-bars for indoor carpet (rubber)? 1.4mm is standard on the car.
Regards Ronny
FF: 3.0
FR: 2.0
RF: 0.0
RR: 3.5
Can you please explain with a few words the reasoning for these changes?
Does anyone else have an opinion on this?
I bought the spring sets so I should be OK there. What about the sway-bars for indoor carpet (rubber)? 1.4mm is standard on the car.
Regards Ronny
#1391
Tech Elite
iTrader: (19)
If I understand you correctly then it should be like below:
FF: 3.0
FR: 2.0
RF: 0.0
RR: 3.5
Can you please explain with a few words the reasoning for these changes?
Does anyone else have an opinion on this?
I bought the spring sets so I should be OK there. What about the sway-bars for indoor carpet (rubber)? 1.4mm is standard on the car.
Regards Ronny
FF: 3.0
FR: 2.0
RF: 0.0
RR: 3.5
Can you please explain with a few words the reasoning for these changes?
Does anyone else have an opinion on this?
I bought the spring sets so I should be OK there. What about the sway-bars for indoor carpet (rubber)? 1.4mm is standard on the car.
Regards Ronny
#1392
Tech Fanatic
iTrader: (11)
Ronny,
Get the swaybar set as it is an important tuning tool. 1.8, 1.6, 1.2mm bars.
The reasoning for Patto's changes to the front is to widen it up and take away some steering. It can also be achieved somewhat by getting the +1mm offset wheel hexes.
Get some 0.5mm suspension block spacers too for the rear.
Get the swaybar set as it is an important tuning tool. 1.8, 1.6, 1.2mm bars.
The reasoning for Patto's changes to the front is to widen it up and take away some steering. It can also be achieved somewhat by getting the +1mm offset wheel hexes.
Get some 0.5mm suspension block spacers too for the rear.
#1393
Thanks guys, much appropriated. I will order the 3.5 suspension mount, 0.5mm spacers and sway bar set.
Are you guys running a gear diff or the spool in the front? I was thinking to run the gear diff with thick fluid (300.000-600.000).
Are you guys running a gear diff or the spool in the front? I was thinking to run the gear diff with thick fluid (300.000-600.000).
#1394
Tech Adept
Hey Ronny finaly you came to sense Going to run rubber or?
You should get the 19T Alu pully, i noticed that the plastic ones got sloppy right away.
You should get the 19T Alu pully, i noticed that the plastic ones got sloppy right away.
Last edited by Team_Elli; 10-18-2011 at 09:12 AM.
#1395
I expected that you would chime in! I will try rubber to begin with. It will for sure be a change as I've always been running on foam. I will add the 19t alu pulley to the "to order" list.