Tekin RS ESC sensored
Tech Elite
iTrader: (124)
lol get out of here.
its a great program has spread sheets, word processor and more. And its Free
http://www.openoffice.org
its a great program has spread sheets, word processor and more. And its Free
its a great program has spread sheets, word processor and more. And its Free
setup for 2wd with 13.5
Hey all, I have not raced electric 1/10 2wd for 10 years and esc have changed alot, also now brushless is the in. My question is can you all give me a basic all around set up for 2wd buggy with a 13.5 (ballistic) (I use to be orange only and am a convert to Tekin) It is a bit overwhelming with the adjustment available with these esc, I am sloowly getting the hang of it but have alot to learn. Thank you in advance, oh I do have the hotwire and have downloaded the vegas 208 sofware.
Sorry I just realized I was lookin on the onroad forum, my bad.
Tech Elite
iTrader: (124)
Well i wanted to test my speed today against the other racers , but tha didn't happen , the rain decided to come and play , so fast laps were out the window
The speedo worked perfectly in its waterproof freezer box
I now need a v208, 13.5 set up for an indoor track with a 30m straight and the rest is technical , it is low grip too (for carpet)
any ideas for a starting point as i have no idea
Thanks in advance Phil
The speedo worked perfectly in its waterproof freezer box
I now need a v208, 13.5 set up for an indoor track with a 30m straight and the rest is technical , it is low grip too (for carpet)
any ideas for a starting point as i have no idea
Thanks in advance Phil
Tech Addict
iTrader: (14)
Sorry up front if I overlooked something.` I briefly searched the last few pages of the forum.
I'm looking for a 17.5 setup for the new 208 software. I got a few off of Tekin's website but I would like to compare several. I will be using this for rubber touring car in doors on carpet. Track size is on the small side. Any help would be great. If you find it easier, you can PM me. Thanks.
I'm looking for a 17.5 setup for the new 208 software. I got a few off of Tekin's website but I would like to compare several. I will be using this for rubber touring car in doors on carpet. Track size is on the small side. Any help would be great. If you find it easier, you can PM me. Thanks.
Tech Lord
iTrader: (103)
Sorry up front if I overlooked something.` I briefly searched the last few pages of the forum.
I'm looking for a 17.5 setup for the new 208 software. I got a few off of Tekin's website but I would like to compare several. I will be using this for rubber touring car in doors on carpet. Track size is on the small side. Any help would be great. If you find it easier, you can PM me. Thanks.
I'm looking for a 17.5 setup for the new 208 software. I got a few off of Tekin's website but I would like to compare several. I will be using this for rubber touring car in doors on carpet. Track size is on the small side. Any help would be great. If you find it easier, you can PM me. Thanks.
end 12500
50 timing boost
fdr 6.5
if in need a little snap add motor timing 5* at a time check temps every couple min
Profiles
The TP is printed on the case of the RS next to the LEDs. It used to stand for throttle profiles. Now it stands for timing profiles. I don't know where the NW suggestion above came from.
To choose from TP1-TP5 and C1-C2 without using the HW, turn the esc on, press and release the mode button. The first LED will blink. Press and release the mode button until the LED next to TP lights up. Press and release the increase button then to choose between the timing profiles. Led1=TP1 LED5=TP5. LED 6 and 7 = C1 and C2 respectively. Of course the values for C1 and C2 can only be adjusted via the hotwire.
The directions to change timing profiles are the same as whats in the manual to change throttle profiles
To choose from TP1-TP5 and C1-C2 without using the HW, turn the esc on, press and release the mode button. The first LED will blink. Press and release the mode button until the LED next to TP lights up. Press and release the increase button then to choose between the timing profiles. Led1=TP1 LED5=TP5. LED 6 and 7 = C1 and C2 respectively. Of course the values for C1 and C2 can only be adjusted via the hotwire.
The directions to change timing profiles are the same as whats in the manual to change throttle profiles
I was looking on Tekin's site for setup sheets for 1s 13.5 WGT but couldn't find any. There are a couple of 1/12 13.5 setups on there, so my question is shouldn't those be fairly close due to the same power and motor? Maybe just drop a tooth or two on the pinion due to the difference in weight? (730g for 1/12, 930g for WGT). Or am I way off here?
Hey guy,s
I have a question about 1/12th. I have a Tekin rs and I plan to run 1c 3.7 13.5 lipo, I was thinking about useing LRP's capacitor would it be ok to use this capacitor here's the part# and what I'm talking about.
Works Team ESC Capacitor, 3.7-4.8v
Part#: LRP 82530
http://www.nexusracing.com/product_i...oducts_id=3122
I have a question about 1/12th. I have a Tekin rs and I plan to run 1c 3.7 13.5 lipo, I was thinking about useing LRP's capacitor would it be ok to use this capacitor here's the part# and what I'm talking about.
Works Team ESC Capacitor, 3.7-4.8v
Part#: LRP 82530
http://www.nexusracing.com/product_i...oducts_id=3122
Originally Posted by sidecarphil1
I now need a v208, 13.5 set up for an indoor track with a 30m straight and the rest is technical , it is low grip too (for carpet)
any ideas for a starting point as i have no idea
Thanks in advance Phil