Kyosho VoneR Thread
Tech Adept
check out the S710 Thread,cool pics of the car with SSG hop ups.
Originally posted by CyrilJ88
thanks guys,
one more question(hope so):
Which brand makes the lowest engine mounting for the Evo?
If I lower my engine,do I need to get the Kawahara micro clutch?
thanks guys,
one more question(hope so):
Which brand makes the lowest engine mounting for the Evo?
If I lower my engine,do I need to get the Kawahara micro clutch?
Last edited by Manticore; 03-15-2004 at 07:29 PM.
pics
here is another..1/10 lola
mike
mike
Last edited by mikecatts; 08-13-2010 at 02:28 PM.
Re: pics
Originally posted by mikecatts
here is another..1/10 lola
mike
here is another..1/10 lola
mike
on e
1/10 chysler
Last edited by mikecatts; 08-13-2010 at 02:28 PM.
1/10 dodge
1/10 dodge
Last edited by mikecatts; 08-13-2010 at 02:28 PM.
235's
the old 235 days
Last edited by mikecatts; 08-13-2010 at 02:28 PM.
1/10 chyrsler
1/10 chrysler
Last edited by mikecatts; 08-13-2010 at 02:28 PM.
JEALOUZ !
Tech Elite
engine mount for FW05
Originally posted by Manticore
you can use the clutch set and engine mount for FW05R but your clutch bell will get into the main chassis if you dont make clearence on the main chassis.
you can use the clutch set and engine mount for FW05R but your clutch bell will get into the main chassis if you dont make clearence on the main chassis.
Is the hole spacing the same as the V1?
I tried the Mugen mounts, but the hole spacing was different and the flywheel was no longer centered in the chassis cutout.
There is another 1/8" to go lower if I can find the right mounts.
Thanks,
Re: engine mount for FW05
Originally posted by popsracer
Manticore;
Is the hole spacing the same as the V1?
I tried the Mugen mounts, but the hole spacing was different and the flywheel was no longer centered in the chassis cutout.
There is another 1/8" to go lower if I can find the right mounts.
Thanks,
Manticore;
Is the hole spacing the same as the V1?
I tried the Mugen mounts, but the hole spacing was different and the flywheel was no longer centered in the chassis cutout.
There is another 1/8" to go lower if I can find the right mounts.
Thanks,
Hi Maticore, i wud like to use the FW05R engine mount on my EVO.
However, i'm using Mugen clutch(4D), and I understand that I need a smaller flywheel, do you know the diameter of the flywheel required & is there any brand out there that i can apply here? Thank.
However, i'm using Mugen clutch(4D), and I understand that I need a smaller flywheel, do you know the diameter of the flywheel required & is there any brand out there that i can apply here? Thank.
Tech Apprentice
Re: engine mount for FW05
Originally posted by popsracer
Manticore;
Is the hole spacing the same as the V1?
I tried the Mugen mounts, but the hole spacing was different and the flywheel was no longer centered in the chassis cutout.
There is another 1/8" to go lower if I can find the right mounts.
Thanks,
Manticore;
Is the hole spacing the same as the V1?
I tried the Mugen mounts, but the hole spacing was different and the flywheel was no longer centered in the chassis cutout.
There is another 1/8" to go lower if I can find the right mounts.
Thanks,
Anyway, rear grip has been improved by using 35wt shock oil + stock springs(rear suspension), setting more rear droop, removing the rear sway bar, and setting front anti-roll bar to 90 degree.
Want to test this car again today...
P.S. I'm using HPI R40 flywheel, clutch weights, and clutch shoe. Others are Kyosho's.
Last edited by wangcc61; 03-17-2004 at 12:40 AM.
Hey thats my setup for max rear grip!! LOL... took me a while to figure it out though
Topcad shocks work well with red springs. Sato Seiki 37 shore tyres with 26mm front and 28mm rear
Topcad shocks work well with red springs. Sato Seiki 37 shore tyres with 26mm front and 28mm rear
low motor
the clutch fly wheel is 33mm and the engine mounts are 14mm...the kawaharra lite v-0ne mounts are the correct height....
Last edited by mikecatts; 08-13-2010 at 02:28 PM.