4LikesNEW HOBBYWING STOCK SUPERCHARGED SOFTWARE
03-30-2011 | 02:24 AM
#4487
Tech Master
Joined: Mar 2009
Posts: 1,316
From: The Netherlands
Make an auto detect firmware, which detects the Lipo type, motor type, driver type, track type and then automatically sets itself.
Then all this talking about timing/steps/boost/ramps/best settings for which motor is history, and most here can focus on racing, instead of spending hours on this thread asking the same questions over and over again....
Yes, my 1/12 is on the shelf, it's 8th scale nitro racing time again, and to be honest, I'm glad!...
So much more power, no battery charging just make a pitstop, refuel and race on, 30 minute finals, no tire traction juice, and keeping up the time, and what if a previous final has some delay.....
Then all this talking about timing/steps/boost/ramps/best settings for which motor is history, and most here can focus on racing, instead of spending hours on this thread asking the same questions over and over again....
Yes, my 1/12 is on the shelf, it's 8th scale nitro racing time again, and to be honest, I'm glad!...
So much more power, no battery charging just make a pitstop, refuel and race on, 30 minute finals, no tire traction juice, and keeping up the time, and what if a previous final has some delay.....
Setting up a esc is nothing more then setting up a nitro engine, look at the stikies ontop of the nitro section in MBF forum and all the questions about setting up a nitro engine over and over again
so much more noise and smell as well....uh WHAT DID YOU SAY?!
03-30-2011 | 02:30 AM
#4489
Thread Starter
Tech Elite
Joined: Nov 2007
Posts: 3,338
+1
Now, I know I have retired from this Thread, but I just wanted to post a link to, what I hope will be a great resource thread
HERE ------> http://www.rctech.net/forum/electric...ings-only.html please, please read the 'Rules' before posting on it, as I don't wish for it to become bogged down in the negativity and pointlessness of this thread. IT IS PURELY for SETUPS ONLY. Thanks to Sosidge, Irgo et al for letting me see the light and helping me in my decision to move away from this thread, life is so much simpler now.
Am back to my old self now, think the break has done me the world of good, hopefully I can help / advise / blow up a few more ESC's on your behalf etc etc
By the way all stock is back in had a bit of a glitch for a while there
Now, I know I have retired from this Thread, but I just wanted to post a link to, what I hope will be a great resource thread
HERE ------> http://www.rctech.net/forum/electric...ings-only.html please, please read the 'Rules' before posting on it, as I don't wish for it to become bogged down in the negativity and pointlessness of this thread. IT IS PURELY for SETUPS ONLY. Thanks to Sosidge, Irgo et al for letting me see the light and helping me in my decision to move away from this thread, life is so much simpler now.Am back to my old self now, think the break has done me the world of good, hopefully I can help / advise / blow up a few more ESC's on your behalf
etc etcBy the way all stock is back in had a bit of a glitch for a while there
Your setup sheets ,your videos and many more .
NOW GET YOUR ASS BACK HERE NOW STUART .DO YOU HEAR ME .
03-30-2011 | 02:49 AM
#4490
Come see me at STCC this year
If anybody wants to come over for a chat/advice feel free....
just look for my car, it is distinctive with a PUKE paint job --->
Or just look out for the 5 Foot Hobbywing Banner on or around our Pit Area BAD PIC BTW ----->
Always happy to talk for AGES hope I can be of some help.
just look for my car, it is distinctive with a PUKE paint job --->
Or just look out for the 5 Foot Hobbywing Banner on or around our Pit Area BAD PIC BTW ----->
Always happy to talk for AGES hope I can be of some help.
03-30-2011 | 03:21 AM
#4493
how about a dual mode... sensored for the start/low-end and sensorless for top end (for running mod)? 
also, if HW can come up with a piggy back system that will record all the hooplah we need to tune the esc better... small footprint of course... so it will be an external data logger. i know there are others already available but if HW can beat the price....
also, if HW can come up with a piggy back system that will record all the hooplah we need to tune the esc better... small footprint of course... so it will be an external data logger. i know there are others already available but if HW can beat the price....
03-30-2011 | 05:43 AM
#4496
Thread Starter
Tech Elite
Joined: Nov 2007
Posts: 3,338
Ok guys
some news we do have a new programming method and a new esc .
one will be our new 3 pin connector not associated with the rx port which will benefit you guys and not have to remove it from the receiver.
The other is a miniture blue tooth interface small enough to fit in you car (will be an option (smart phone applications will be available)
The lcd 2 in 1 will have a bluetooth interface to work with the car module.
The reson why we cannot build into the esc as the size will be big for the esc and because of noise as esc's do have high currents even on idle which would cause the esc to go offline all the time .The 1/8th scale esc because of it's massive size we will probably have the blue tooth built in but we need to see after testing if it will work .
The bluetooth unit will be very small the size of a fail safe unit .You will still have the option of direct plug in through the new connector direct to the 2 in 1 programmer .
so as you can see we are moving forward .All this will have patents attached to protect michael's and the teams hard work .
keep you all informed .this is probably going to be available late sep 2011 first prototype end of july .
some news we do have a new programming method and a new esc .
one will be our new 3 pin connector not associated with the rx port which will benefit you guys and not have to remove it from the receiver.
The other is a miniture blue tooth interface small enough to fit in you car (will be an option (smart phone applications will be available)
The lcd 2 in 1 will have a bluetooth interface to work with the car module.
The reson why we cannot build into the esc as the size will be big for the esc and because of noise as esc's do have high currents even on idle which would cause the esc to go offline all the time .The 1/8th scale esc because of it's massive size we will probably have the blue tooth built in but we need to see after testing if it will work .
The bluetooth unit will be very small the size of a fail safe unit .You will still have the option of direct plug in through the new connector direct to the 2 in 1 programmer .
so as you can see we are moving forward .All this will have patents attached to protect michael's and the teams hard work .
keep you all informed .this is probably going to be available late sep 2011 first prototype end of july .
03-30-2011 | 06:05 AM
#4497
Tech Master
Joined: Nov 2002
Posts: 1,099
From: Parts Unkown
Ok guys
some news we do have a new programming method and a new esc .
one will be our new 3 pin connector not associated with the rx port which will benefit you guys and not have to remove it from the receiver.
The other is a miniture blue tooth interface small enough to fit in you car (will be an option (smart phone applications will be available)
The lcd 2 in 1 will have a bluetooth interface to work with the car module.
The reson why we cannot build into the esc as the size will be big for the esc and because of noise as esc's do have high currents even on idle which would cause the esc to go offline all the time .The 1/8th scale esc because of it's massive size we will probably have the blue tooth built in but we need to see after testing if it will work .
The bluetooth unit will be very small the size of a fail safe unit .You will still have the option of direct plug in through the new connector direct to the 2 in 1 programmer .
so as you can see we are moving forward .All this will have patents attached to protect michael's and the teams hard work .
keep you all informed .this is probably going to be available late sep 2011 first prototype end of july .
some news we do have a new programming method and a new esc .
one will be our new 3 pin connector not associated with the rx port which will benefit you guys and not have to remove it from the receiver.
The other is a miniture blue tooth interface small enough to fit in you car (will be an option (smart phone applications will be available)
The lcd 2 in 1 will have a bluetooth interface to work with the car module.
The reson why we cannot build into the esc as the size will be big for the esc and because of noise as esc's do have high currents even on idle which would cause the esc to go offline all the time .The 1/8th scale esc because of it's massive size we will probably have the blue tooth built in but we need to see after testing if it will work .
The bluetooth unit will be very small the size of a fail safe unit .You will still have the option of direct plug in through the new connector direct to the 2 in 1 programmer .
so as you can see we are moving forward .All this will have patents attached to protect michael's and the teams hard work .
keep you all informed .this is probably going to be available late sep 2011 first prototype end of july .
Keep up the good work
03-30-2011 | 06:31 AM
#4498
Tech Elite
Joined: Dec 2004
Posts: 2,198
From: The Netherlands
03-30-2011 | 07:18 AM
#4500
Tech Fanatic
Joined: Apr 2006
Posts: 893
Interesting Angelo,
imagine what Shizeng said previously,
wireless Programming, How far is the Blue tooth can handle ?
I thought Mr. Pan (Hobbywing Crossover) will released The Wireless Power?
Gasket (water,Dirt,Dust Proof)
Motor Temp Cut-Off ex: off,40°C,50°C,60°,70°C,Custom°,factory°.
more Motor Stator tech,anti vibration coils,etc?
and i hope Hobbywing thinking of much more fun,better,tech not just race for touring,
because a lots of them out there is like to Bashing, Crawling, and, Drifting,
and most of them i know like to get the xerun 2.0 to do all that thing.
Previously Black and Blue, colour is Great, but i think it's best to that
Clear transparent one without paint,
and not just for Hobbywing, i hope you Angelo can show a cheaper 10000mah lipo, for the Fanatic's who like's to beat Gas Duration.
and spread to the world wide.
there is more, but i would like to keep it private just for you Angelo and Mr.Michael.
imagine what Shizeng said previously,
wireless Programming, How far is the Blue tooth can handle ?
I thought Mr. Pan (Hobbywing Crossover) will released The Wireless Power?
Gasket (water,Dirt,Dust Proof)
Motor Temp Cut-Off ex: off,40°C,50°C,60°,70°C,Custom°,factory°.
more Motor Stator tech,anti vibration coils,etc?
and i hope Hobbywing thinking of much more fun,better,tech not just race for touring,
because a lots of them out there is like to Bashing, Crawling, and, Drifting,
and most of them i know like to get the xerun 2.0 to do all that thing.
Previously Black and Blue, colour is Great, but i think it's best to that
Clear transparent one without paint,
and not just for Hobbywing, i hope you Angelo can show a cheaper 10000mah lipo, for the Fanatic's who like's to beat Gas Duration.
and spread to the world wide.
there is more, but i would like to keep it private just for you Angelo and Mr.Michael.