4LikesNEW HOBBYWING STOCK SUPERCHARGED SOFTWARE
12-20-2010 | 01:57 PM
#1996
Tech Elite
Joined: Dec 2004
Posts: 2,198
From: The Netherlands
Only if you install a software version with only 10 settings, you don't need the program box, if you install the latest software version with 15 setting, you do need the box....
12-20-2010 | 02:36 PM
#1997
Thread Starter
Tech Elite
Joined: Nov 2007
Posts: 3,338
this Q has been asked at 2 thread, but no response... hope here i will get the answer... i am user of ezrun 5.5t n xerun 2.1 120A...
for the esc with dynamic timing (without supercharge/turbo timing)... let say the motor rpm limit is about at 8000rpm on load... and max esc timing is 20deg (motor timing is 0deg) ...
1. is that mean at max rpm/8000rpm will be at max timing/20deg (same with max speed i guess)...?
2. if the throttle at 40%, is the timing introduced to the motor will be at 8deg...? (40% of 20deg)
3. same with no2 Q, if throttle trigger hard from 0% - 100%... is max timing will be introduced at low rpm too...?
4. max speed is max rpm... is the max speed is about limit of current (max Amp) which apply to motor from esc, or it is caused by max timing...?
for the esc with dynamic timing (without supercharge/turbo timing)... let say the motor rpm limit is about at 8000rpm on load... and max esc timing is 20deg (motor timing is 0deg) ...
1. is that mean at max rpm/8000rpm will be at max timing/20deg (same with max speed i guess)...?
2. if the throttle at 40%, is the timing introduced to the motor will be at 8deg...? (40% of 20deg)
3. same with no2 Q, if throttle trigger hard from 0% - 100%... is max timing will be introduced at low rpm too...?
4. max speed is max rpm... is the max speed is about limit of current (max Amp) which apply to motor from esc, or it is caused by max timing...?
2.yes will be at 40% as the timing set to say 26 degree doesnt mean you will have the max timing at 40% throttle it will ramp up in a linear movement as you throttle to full power .
3.yes you will have max timing at full throttle even at low rpm as the rpm ramps up as your ramming the power at an instant.
4 caused by max timing as the timing will control the current flow through the esc.
12-20-2010 | 06:09 PM
#1998
Tech Addict
Joined: Dec 2009
Posts: 721
1.no motor has zero timing may it be mechanical or fixed .Mechanical on zero position still have 3 -6 degree timing not matter what brand and fixed timing say zero but they sit at about 18-22 degree.
2.yes will be at 40% as the timing set to say 26 degree doesnt mean you will have the max timing at 40% throttle it will ramp up in a linear movement as you throttle to full power .
3.yes you will have max timing at full throttle even at low rpm as the rpm ramps up as your ramming the power at an instant.
4 caused by max timing as the timing will control the current flow through the esc.
2.yes will be at 40% as the timing set to say 26 degree doesnt mean you will have the max timing at 40% throttle it will ramp up in a linear movement as you throttle to full power .
3.yes you will have max timing at full throttle even at low rpm as the rpm ramps up as your ramming the power at an instant.
4 caused by max timing as the timing will control the current flow through the esc.
12-21-2010 | 08:23 PM
#1999
Thread Starter
Tech Elite
Joined: Nov 2007
Posts: 3,338
In the last couple of months i have been doing a crack down on fake hobbywing goods and online stores .
There seesm to be alot of them out there and we are working through everyone of them .so be careful what you buy and from where you buy it from .
They seem to use the hobbywing logos on there sites and pictures also but all products are 100% fakes .especially the aircraft and ez run 35 amp and 60 amp .
This website is one of them
http://www.targethobby.com/
I will post more and more as they surface .
Our customers are very important to us and we must protect not only them but our brand and product.
please if you see anything out there or you have bought a product that just doesnt seem right to you please let us know by email at
teamcobraracing@gmail or [email protected]
ive posted some sample the bec we have only two wire config not three like this one . our circiuts are red not green like these ones and have a look at the solder quality and these are heatshrinked hobbywing wow.and many more .
There seesm to be alot of them out there and we are working through everyone of them .so be careful what you buy and from where you buy it from .
They seem to use the hobbywing logos on there sites and pictures also but all products are 100% fakes .especially the aircraft and ez run 35 amp and 60 amp .
This website is one of them
http://www.targethobby.com/
I will post more and more as they surface .
Our customers are very important to us and we must protect not only them but our brand and product.
please if you see anything out there or you have bought a product that just doesnt seem right to you please let us know by email at
teamcobraracing@gmail or [email protected]
ive posted some sample the bec we have only two wire config not three like this one . our circiuts are red not green like these ones and have a look at the solder quality and these are heatshrinked hobbywing wow.and many more .
12-23-2010 | 03:32 PM
#2003
Tech Adept
Joined: Jan 2010
Posts: 147
funny u shld say that
12-23-2010 | 03:44 PM
#2004
Tech Regular
Joined: Sep 2009
Posts: 398
From: Netherlands
sent a PM to the guy from youre thread too.
Maybe Cobra cann explain some off the features.
12-23-2010 | 04:30 PM
#2006
Tech Regular
Joined: Sep 2009
Posts: 398
From: Netherlands
12-23-2010 | 10:30 PM
#2007
Tech Apprentice
Joined: Jul 2010
Posts: 85
From: Under MoonLight
12-23-2010 | 10:59 PM
#2008
Thread Starter
Tech Elite
Joined: Nov 2007
Posts: 3,338
Guys you are so quick i got to give it to you yes there is something new coming out as we are going from your normal c programming to C++ so many news things coming your way in the new year .
12-24-2010 | 01:58 AM
#2009
Tech Adept
Joined: Feb 2010
Posts: 141
From: UK
12-24-2010 | 09:40 AM
#2010
Tech Regular
Joined: Sep 2009
Posts: 398
From: Netherlands
man we are fast....lol....for sure when we drive the HW..!!
Nice to hear that c++ is on the way, once learned to use it when studying.
Think it`s difficult.
Hope you will give us a nice write up when its there.
Kind regards,
Roy
PS. more and more people are starting to use the HW overhere in the Netherlands.