6LikesRB Concept Engine Thread
07-26-2010 | 06:56 PM
#511
Tech Fanatic
iTrader: (6)
Joined: Feb 2007
Posts: 923
The 2604 or the Capricorn 2662 work best.
I like the 2604 the best, the 2662 gives it a higher top speed but less bottom/mid power.
The 2630 is a useless pipe if you ask me, uses a lot of fuel and creates a lot of heat with less power as most other pipes.
If you want a nova pipe get the 2660 instead.
I like the 2604 the best, the 2662 gives it a higher top speed but less bottom/mid power.
The 2630 is a useless pipe if you ask me, uses a lot of fuel and creates a lot of heat with less power as most other pipes.
If you want a nova pipe get the 2660 instead.
07-27-2010 | 07:06 PM
#513
Tech Fanatic
iTrader: (6)
Joined: Feb 2007
Posts: 923
for 25% nitro on a RB TJ10, you guys recommend adding a .1 or .2 shim?
i need to buy some shims - will these fit http://www.amainhobbies.com/product_...n/RB-Head-Shim
i need to buy some shims - will these fit http://www.amainhobbies.com/product_...n/RB-Head-Shim
Last edited by LiL_JaSoN; 07-27-2010 at 07:47 PM.
07-27-2010 | 07:57 PM
#514
Tech Addict
iTrader: (21)
Joined: May 2007
Posts: 624
for 25% nitro on a RB TJ10, you guys recommend adding a .1 or .2 shim?
i need to buy some shims - will these fit http://www.amainhobbies.com/product_...n/RB-Head-Shim
i need to buy some shims - will these fit http://www.amainhobbies.com/product_...n/RB-Head-Shim
07-27-2010 | 08:06 PM
#515
Tech Fanatic
iTrader: (6)
Joined: Feb 2007
Posts: 923
http://www.amainhobbies.com/product_...-020mm-0008-28
this one? :S
or this - http://www.amainhobbies.com/product_.../RB-Head-Shims
it says for .21 but also fits junior 9 etc
07-27-2010 | 09:09 PM
#516
Tech Addict
iTrader: (21)
Joined: May 2007
Posts: 624
looking at the packet of the picture, it says they are 0.3 thanks for that.
http://www.amainhobbies.com/product_...-020mm-0008-28
this one? :S
or this - http://www.amainhobbies.com/product_.../RB-Head-Shims
it says for .21 but also fits junior 9 etc
http://www.amainhobbies.com/product_...-020mm-0008-28
this one? :S
or this - http://www.amainhobbies.com/product_.../RB-Head-Shims
it says for .21 but also fits junior 9 etc
These are what you want:
http://www.serpentamerica.com/shop/p...6&cat=9&page=1
07-27-2010 | 09:20 PM
#517
Tech Fanatic
iTrader: (6)
Joined: Feb 2007
Posts: 923
They made a junior 9 .21 buggy engine also so those won't work.
These are what you want:
http://www.serpentamerica.com/shop/p...6&cat=9&page=1
These are what you want:
http://www.serpentamerica.com/shop/p...6&cat=9&page=1
but found them elsewhere
http://shopping.rcmodel.hk/product_i...10jfpk428o2625
or should i get the .15
http://shopping.rcmodel.hk/product_i...ducts_id=14708
Last edited by LiL_JaSoN; 07-27-2010 at 10:03 PM.
07-28-2010 | 04:59 AM
#518
Tech Addict
iTrader: (21)
Joined: May 2007
Posts: 624
only problem is.. postage is $93.. lol
but found them elsewhere
http://shopping.rcmodel.hk/product_i...10jfpk428o2625
or should i get the .15
http://shopping.rcmodel.hk/product_i...ducts_id=14708
but found them elsewhere
http://shopping.rcmodel.hk/product_i...10jfpk428o2625
or should i get the .15
http://shopping.rcmodel.hk/product_i...ducts_id=14708
ordered.
07-28-2010 | 02:40 PM
#520
On the RB K9/K10 run a total of 3 x 0.22 mm shims for 30%....They are the included shims with the engine...some of these engines came with 4 shims, some came with 3 shims.....however for 30% fuel 3 shims is about right, 4 shims is too many and lowers the compression too much IMO ..
07-28-2010 | 03:19 PM
#521
07-29-2010 | 09:07 AM
#522
Tech Apprentice
Joined: Oct 2007
Posts: 50
From: G-Town
07-30-2010 | 09:49 AM
#524
Tech Apprentice
Joined: Oct 2007
Posts: 50
From: G-Town
I dont know if nova plus will work, fit yes Im sure somebody knows. Seen the piston and sleeve set on A main hobbies under engine parts. From what I was told it has a little higher exhaust port.
07-30-2010 | 09:55 AM
#525
