Trinity EXTECH .21
03-20-2009 | 10:39 AM
#1426
Tech Apprentice
Joined: Feb 2009
Posts: 55
From: El Monte, CA
03-20-2009 | 10:45 AM
#1427
Tech Apprentice
Joined: Feb 2009
Posts: 55
From: El Monte, CA
I use the stock hanger from Kyosho. It's the straight one that you hafta bend to your liking. And fitted perfectly.
03-21-2009 | 11:10 AM
#1433
Tech Fanatic
iTrader: (25)
Joined: Jan 2005
Posts: 966
From: Wauconda, IL
Last question I hope, I got the pipe all mounted and I started to take the engines apart to make sure they had the right head shims in them and all clean inside and I had a very hard time getting the head off of 1 of the engines because of the flat head scres that it has but managed to get it off. The next one I was able to strip out 3 of the 4 screws and break the tip off of a screw driver. WHO puts these together that the head needs to be so tight you have to twist that hard, I mean really.
So I guess my question is how do I get the head off now? I have never had this problem and a little irratated about the situation.
Way to tight on the cooling head screws Trinity but other then that they look great and I cant wait to break it in today.
So I guess my question is how do I get the head off now? I have never had this problem and a little irratated about the situation.
Way to tight on the cooling head screws Trinity but other then that they look great and I cant wait to break it in today.
03-21-2009 | 12:50 PM
#1434
Tech Addict
iTrader: (36)
Joined: Jun 2006
Posts: 664
From: Boligee AL.
.24
Hey Todd, (Team Chambers)
After pitting for you at the Twister, and watchin' your truck, listening to it, the idle, all that, I AM SOLD!!! on the .24 Extech, my sis and Dad both bought them as well. Im going to sell all of my trucks, maxxs, savages, Losi everything, and get me the new 2.0, and the .24 is goin in there too! Such a pimp motor, and this thread is only helping me choose!
BTW, Tear em' up at Phoenix!
After pitting for you at the Twister, and watchin' your truck, listening to it, the idle, all that, I AM SOLD!!! on the .24 Extech, my sis and Dad both bought them as well. Im going to sell all of my trucks, maxxs, savages, Losi everything, and get me the new 2.0, and the .24 is goin in there too! Such a pimp motor, and this thread is only helping me choose!
BTW, Tear em' up at Phoenix!
03-22-2009 | 08:17 AM
#1436
Tech Master
Joined: Dec 2003
Posts: 1,418
From: Amishland PA
Last question I hope, I got the pipe all mounted and I started to take the engines apart to make sure they had the right head shims in them and all clean inside and I had a very hard time getting the head off of 1 of the engines because of the flat head scres that it has but managed to get it off. The next one I was able to strip out 3 of the 4 screws and break the tip off of a screw driver. WHO puts these together that the head needs to be so tight you have to twist that hard, I mean really.
So I guess my question is how do I get the head off now? I have never had this problem and a little irratated about the situation.
Way to tight on the cooling head screws Trinity but other then that they look great and I cant wait to break it in today.
So I guess my question is how do I get the head off now? I have never had this problem and a little irratated about the situation.
Way to tight on the cooling head screws Trinity but other then that they look great and I cant wait to break it in today.
03-22-2009 | 08:37 AM
#1437
Tech Fanatic
iTrader: (25)
Joined: Jan 2005
Posts: 966
From: Wauconda, IL
Chad: It's all good man I went out and bought a new screw driver to fit casue I didn't have one @ the house.
I ran 4 tanks for a quick break in yesterday on the street and man I'm in love with these mills. Temps never where over 188 and LOTS of power, I know it's not race conditions but I almost got 13 min on a tank of fuel with the Big Boy Pipe and OD 97t Plug.
LOT THE EXTECH that is for sure, great work Chad and the rest of the Trinity team behind the new mills
I ran 4 tanks for a quick break in yesterday on the street and man I'm in love with these mills. Temps never where over 188 and LOTS of power, I know it's not race conditions but I almost got 13 min on a tank of fuel with the Big Boy Pipe and OD 97t Plug.
LOT THE EXTECH that is for sure, great work Chad and the rest of the Trinity team behind the new mills
03-22-2009 | 08:47 AM
#1438
Tech Adept
Joined: Apr 2008
Posts: 191
Here's my truggy w\ the .24 and BigBoy pipe.
I used the GMK Spring Thing for pipe mount. http://www.amainhobbies.com/product_...oducts_id/5233
I used the GMK Spring Thing for pipe mount. http://www.amainhobbies.com/product_...oducts_id/5233