JConcepts Thread
#1321
Company Representative
iTrader: (20)
you can kinda get away without doing it because the inside rib is smaller. i just mounted a set of pink tapers and cut them anyways, better to be safe then gluing my fingers together trying to get the tire in the bead
oh yeah since were showing bodies, here's a pic of all the wonderment that is j concepts oh yeah the radio is all paint and 707paint.net is almost ready for launch.
oh yeah since were showing bodies, here's a pic of all the wonderment that is j concepts oh yeah the radio is all paint and 707paint.net is almost ready for launch.
#1322
Here's my B4 with the JConcepts touch...
Last edited by FOXY923; 12-07-2008 at 09:40 PM.
#1323
Tech Champion
iTrader: (33)
you can kinda get away without doing it because the inside rib is smaller. i just mounted a set of pink tapers and cut them anyways, better to be safe then gluing my fingers together trying to get the tire in the bead
oh yeah since were showing bodies, here's a pic of all the wonderment that is j concepts oh yeah the radio is all paint and 707paint.net is almost ready for launch.
oh yeah since were showing bodies, here's a pic of all the wonderment that is j concepts oh yeah the radio is all paint and 707paint.net is almost ready for launch.
#1325
you can kinda get away without doing it because the inside rib is smaller. i just mounted a set of pink tapers and cut them anyways, better to be safe then gluing my fingers together trying to get the tire in the bead
oh yeah since were showing bodies, here's a pic of all the wonderment that is j concepts oh yeah the radio is all paint and 707paint.net is almost ready for launch.
oh yeah since were showing bodies, here's a pic of all the wonderment that is j concepts oh yeah the radio is all paint and 707paint.net is almost ready for launch.
Looking good, FastCats is in Canada, right?
#1326
Company Representative
iTrader: (20)
It turned out lookin pretty cool. you should see the detail in it, the silver and black is all skulls and bones!! And then the whole thing has 4 coats of clear. way to much time on my hands, not to mention a few screws left over from the rebuild (......now where did those go!!!) LOL I just wish there was a better way to put pics up, th pic looks awful.
#1327
I agree.
Yes, Oakville Ontario. Check out the site FastCats.ca. It's a world class facility (more than just a track)
#1328
Andy Moore- YGPM
#1329
Yes, Oakville Ontario. Check out the site FastCats.ca. It's a world class facility (more than just a track)
Replied. Here is a pic of my car for whatever reason. Im using B44 caster blocks, steering blocks, rear arms, rear hubs, and front hexes. The car was also update with the WE steering bellcranks, steering rack, direct shaft kit, and a rear sway bar.
#1330
So andy are there any plans to up grade the BJ4WE to compete with the B44?
#1331
Advise needed,
I am going to get myself a BJ4WE and I am thinking about an Orion Vortex 5.5 brushless motor. has any one used one of these and what speedy should I get to go with it. I also want to go lipo so what else would I need and what packs do people recomend
I am going to get myself a BJ4WE and I am thinking about an Orion Vortex 5.5 brushless motor. has any one used one of these and what speedy should I get to go with it. I also want to go lipo so what else would I need and what packs do people recomend
#1332
The Orion motors are great, you'll be more than satisfied it the speed. I, along with many others use the LRP speedo with their Orion motors. As far as a saddle LiPo, I would wait for someone to release a hard case version.
#1333
Tech Addict
iTrader: (2)
If I remember right Reedy is going to make a hard case Li-Po, and I think there is another company that will make one as well. Max amps makes a hard case to go over their packs as well, although I am going to wait for the Reedy packs to come out (for my BJ4 worlds that is in my avatar (the other car is a T4)).