Yokomo YZ-2
|
|||
#3961
Do you guys just use the older non-offset CA 0deg hubs, CA rear camber plate then remove DTM bulkhead/shocktower brace and gtg? The CA gearbox has a tab and 2 screws to secure to the camber link plate, do you run with no gearbox rear bracing when you remove the dtm brace for high grip?
#3962
Tech Adept
Got the aluminium chassis baces too (top plate mounts), an expensive option.
What I liked about the original YZ2 (and the CA to some extend) was the fully equiped car out of the box for astro/carpet and I seem to find that in the CA2 plus lots of little improvements here and there.
Like it !
#3964
Highly suggested
#3965
Tech Champion
iTrader: (21)
Hi could u give me a breif rundown of which CA rear ends parts to swap in for a DTM when the grip is high as you said?
Do you guys just use the older non-offset CA 0deg hubs, CA rear camber plate then remove DTM bulkhead/shocktower brace and gtg? The CA gearbox has a tab and 2 screws to secure to the camber link plate, do you run with no gearbox rear bracing when you remove the dtm brace for high grip?
Do you guys just use the older non-offset CA 0deg hubs, CA rear camber plate then remove DTM bulkhead/shocktower brace and gtg? The CA gearbox has a tab and 2 screws to secure to the camber link plate, do you run with no gearbox rear bracing when you remove the dtm brace for high grip?
#3967
Tech Legend
iTrader: (294)
Basically the ball end that articulates from the servo horn can hit the upper brace in the place where it is already recessed to allow free movement. say this when I went with the Ruddog servo horn on the 20mm setting with a protek 160T servo. I had to dremel it ever so slightly.
New DTM2 announced:
Yokomo YZ-2 DTM2 2WD buggy kit -NeoBuggy.net ? Offroad RC Car News
Price is way up there, $415 on amain, hopefully that is just initially what they are just throwing up out there.
#3968
haven't see his issue on rubbing spring, however, I have seen an issue where the steering can bind depending on the servo horn and servo used.
Basically the ball end that articulates from the servo horn can hit the upper brace in the place where it is already recessed to allow free movement. say this when I went with the Ruddog servo horn on the 20mm setting with a protek 160T servo. I had to dremel it ever so slightly.
New DTM2 announced:
Yokomo YZ-2 DTM2 2WD buggy kit -NeoBuggy.net ? Offroad RC Car News
Price is way up there, $415 on amain, hopefully that is just initially what they are just throwing up out there.
Basically the ball end that articulates from the servo horn can hit the upper brace in the place where it is already recessed to allow free movement. say this when I went with the Ruddog servo horn on the 20mm setting with a protek 160T servo. I had to dremel it ever so slightly.
New DTM2 announced:
Yokomo YZ-2 DTM2 2WD buggy kit -NeoBuggy.net ? Offroad RC Car News
Price is way up there, $415 on amain, hopefully that is just initially what they are just throwing up out there.
#3969
Tech Legend
iTrader: (294)
https://www.amainhobbies.com/yokomo-...z2dtm2/p754644
talked them and it sounds like the price will be the price.
Need to really read the breakdown on this but initially not sure I am seeing $415 of car there.
talked them and it sounds like the price will be the price.
Need to really read the breakdown on this but initially not sure I am seeing $415 of car there.
#3970
https://www.amainhobbies.com/yokomo-...z2dtm2/p754644
talked them and it sounds like the price will be the price.
Need to really read the breakdown on this but initially not sure I am seeing $415 of car there.
talked them and it sounds like the price will be the price.
Need to really read the breakdown on this but initially not sure I am seeing $415 of car there.
#3971
Tech Champion
iTrader: (21)
https://www.amainhobbies.com/yokomo-...z2dtm2/p754644
talked them and it sounds like the price will be the price.
Need to really read the breakdown on this but initially not sure I am seeing $415 of car there.
talked them and it sounds like the price will be the price.
Need to really read the breakdown on this but initially not sure I am seeing $415 of car there.
The CA2 is currently at $415 as well and even as someone who has ran Yokomo buggies since the first plastic chassis B-max2's were available stateside, I would struggle to make the case to anyone looking for a carpet/turf car to buy it at that...
#3973
It says the DTM to comes with the new S3 rear arms?
I wonder if it's S4 arms in the standard length
I wonder if it's S4 arms in the standard length
#3974
Tech Legend
iTrader: (294)
Yokomo's new slogan, "Working to make Xray look affordable"
lol, well for now you still get 2 parts for the price of one xray one like a-arms
The CA2 is currently at $415 as well and even as someone who has ran Yokomo buggies since the first plastic chassis B-max2's were available stateside, I would struggle to make the case to anyone looking for a carpet/turf car to buy it at that...
lol, well for now you still get 2 parts for the price of one xray one like a-arms
The CA2 is currently at $415 as well and even as someone who has ran Yokomo buggies since the first plastic chassis B-max2's were available stateside, I would struggle to make the case to anyone looking for a carpet/turf car to buy it at that...
still up there..