22LikesTekno RC EB48.3 Thread
10-24-2016 | 09:33 PM
#2416
From your setup sheet I'd try 24mm or less front ride height and 1° toe out front.
The camber links are already giving you quite a low front RC compared to the rear RC to a car that, as said, has tons of steer.
My two cents as some says
Edit: Something just went across my mind : what tires are you using ? Sometimes it's as simple a that.
The camber links are already giving you quite a low front RC compared to the rear RC to a car that, as said, has tons of steer.
My two cents as some says
Edit: Something just went across my mind : what tires are you using ? Sometimes it's as simple a that.
10-24-2016 | 09:35 PM
#2417
I'm trying to get a good grasp on wha the pills indicate. Your rear toe is -3.5 degrees right? You posted "0" on your setup sheet, but I figured you just left it blank and didn't actually mean "0" degrees? Am I right?
Last edited by jason07; 10-24-2016 at 09:57 PM.
10-25-2016 | 06:10 AM
#2418
Joined: Dec 2011
Posts: 3,808
From: Texas
10-25-2016 | 08:22 AM
#2419
Tech Master
Joined: Oct 2014
Posts: 1,167
From: Maine
10-25-2016 | 08:39 AM
#2420
I tried searching and didn't find the exact answer.
I'm struggling with off power steering (or just getting through a corner tight vs taking it wide)
I used the Joe Bornhorst setup but I have gotten so far away from that that I'm not sure what to call it.
I am using 7/7/5 in the diffs and I believe 425/ 475 in the shocks. The car just won't turn into the corner, I can't comment if its getting out of the corner well because I have to go so slow to setup for the exit.
Any help would be appreciated.
I'm struggling with off power steering (or just getting through a corner tight vs taking it wide)
I used the Joe Bornhorst setup but I have gotten so far away from that that I'm not sure what to call it.
I am using 7/7/5 in the diffs and I believe 425/ 475 in the shocks. The car just won't turn into the corner, I can't comment if its getting out of the corner well because I have to go so slow to setup for the exit.
Any help would be appreciated.
10-25-2016 | 08:51 AM
#2421
Tech Regular
iTrader: (6)
Joined: Dec 2010
Posts: 340
From: San Diego
Not for some time. We have been using the plastic caps for a while and they are very durable. I personally have never broken one. Several of our team guys have been using them for years and only broken a couple.
10-25-2016 | 08:54 AM
#2422
Suspended
iTrader: (-1)
Joined: May 2016
Posts: 272
From: Daytona, FL
I have never broken a plastic cap on my NB, I was running plastic on the NB for awhile because I hated the look of the scratched up alum... But haven't had any issues with durability.
Is there much of a difference between emul and vented? I run emul on my sct and vented on my buggies, but don't know the actual differences in performance.
Is there much of a difference between emul and vented? I run emul on my sct and vented on my buggies, but don't know the actual differences in performance.
10-25-2016 | 09:00 AM
#2423
Tech Regular
iTrader: (6)
Joined: Dec 2010
Posts: 340
From: San Diego
I have never broken a plastic cap on my NB, I was running plastic on the NB for awhile because I hated the look of the scratched up alum... But haven't had any issues with durability.
Is there much of a difference between emul and vented? I run emul on my sct and vented on my buggies, but don't know the actual differences in performance.
Is there much of a difference between emul and vented? I run emul on my sct and vented on my buggies, but don't know the actual differences in performance.
10-25-2016 | 09:57 AM
#2424
Suspended
iTrader: (-1)
Joined: May 2016
Posts: 272
From: Daytona, FL
Why isn't emulsion recommended for stock setup? When I built my SCT i went emulsion since that is what I used on my Losi SCTE, I never knew the differences between the styles though. I only went it because it's what I knew.
Thanks for clearing up the pros/cons a bit.
Thanks for clearing up the pros/cons a bit.
10-25-2016 | 11:13 AM
#2425
Joined: Dec 2011
Posts: 3,808
From: Texas
If you look on Tekno's website they have updated setup sheets for outdoor, rough outdoor, and indoor.
10-25-2016 | 09:58 PM
#2429
Tech Regular
Joined: Dec 2008
Posts: 365
10-26-2016 | 03:48 AM
#2430
