2LikesTekno RC EB48 Thread
08-15-2013 | 07:32 AM
#8522
Tech Addict
iTrader: (1)
Joined: May 2010
Posts: 609
From: oakdale,new york
so,i have just had the second savox 1256 servo fail on my eb48, i have an early kit and don't have the saver cranked down or locked. any insight on this? savox replaced the first one and now this one has locked up. thanks..
08-15-2013 | 07:48 AM
#8524
. If you have one on backorder somewhere it will be filled with the new kit.I see Tower has not updated there info on the New EB48.2
http://www3.towerhobbies.com/cgi-bin...&I=LXCLTD&P=ML
I want to order one just want to make sure I get the NEW EB48.2 KIT.
Or should I wait till they update their site?
Thank you
08-15-2013 | 07:48 AM
#8525
Is the linkage to the servo at an angle to the servo horn ? This could put stress on the servo . I havent had good luck with Savox , had a 1256 fail from the very first hit put on it .
08-15-2013 | 07:55 AM
#8526
my experience with savox is they get slop almost instantly on my 1/8 scales and this 4wd SC truck class! I'm sorry this is of topic
I'll post in savox post
I'll post in savox post
Last edited by boudin4evr; 08-15-2013 at 07:56 AM. Reason: added to post
08-15-2013 | 08:00 AM
#8527
There is a little bit of angle on it, but noy much. You could shim it up a bit on the saver side.
08-15-2013 | 08:03 AM
#8529
Tech Addict
iTrader: (1)
Joined: May 2010
Posts: 609
From: oakdale,new york
i have the linkage level with no binding. first servo blew out the top bearing, this one locked up. i have a spectrum 8000 but it is tall and you have to cut out the body so the linkage doesn't rub, looks like i will have to try that...
08-15-2013 | 08:20 AM
#8530
08-15-2013 | 09:57 AM
#8531
Hi teknorc,
You are absolutly right about keeping the info to yourselves.
I love the way you manage the EB48 line. You are so reactive with the "bad parts", the "little errors" of the first batchs...
I hope and think the EB48.2 will be a great success too.
I can imagine your designer is one of the happiest one in this industry !
You are one of the company which has understood the first, that 1/8 electric offroad will be a major class in the future, and then you succeed in doing a very recognizable car with a really different design.
The EB48 success here in France, is unbelievable. Great job !
Bye !
You are absolutly right about keeping the info to yourselves.
I love the way you manage the EB48 line. You are so reactive with the "bad parts", the "little errors" of the first batchs...
I hope and think the EB48.2 will be a great success too.
I can imagine your designer is one of the happiest one in this industry !
You are one of the company which has understood the first, that 1/8 electric offroad will be a major class in the future, and then you succeed in doing a very recognizable car with a really different design.
The EB48 success here in France, is unbelievable. Great job !
Bye !
08-15-2013 | 09:59 AM
#8532
Try one of these, you should have better results.
http://www.teknorc.com/?s=tkr525&post_type=product
08-15-2013 | 10:00 AM
#8533
I see Tower has not updated there info on the New EB48.2
http://www3.towerhobbies.com/cgi-bin...&I=LXCLTD&P=ML
I want to order one just want to make sure I get the NEW EB48.2 KIT.
Or should I wait till they update their site?
Thank you
http://www3.towerhobbies.com/cgi-bin...&I=LXCLTD&P=ML
I want to order one just want to make sure I get the NEW EB48.2 KIT.
Or should I wait till they update their site?
Thank you
08-15-2013 | 10:53 AM
#8534
What servo horn are you using? We just came out with some low-mount servo horns because pretty much everything else we tried puts too much stress on the servo shaft.
Try one of these, you should have better results.
http://www.teknorc.com/?s=tkr525&post_type=product
Try one of these, you should have better results.
http://www.teknorc.com/?s=tkr525&post_type=product
I see I'm going to ahve to order this horn...
