57LikesThe Speed Passion Thread
01-30-2013 | 06:22 AM
01-30-2013 | 10:26 AM
Joined: Nov 2002
Posts: 7,758
From: Chicago, IL
01-30-2013 | 11:00 AM
01-30-2013 | 12:09 PM
Tech Apprentice
iTrader: (1)
Joined: Nov 2011
Posts: 87
hi all
I recently got a used SP gt 2.0 LPF. coupled with a novak 13.5t. The problem i have is that there's no throttle, i tried configuring it but all i get is continuous beep.beep.beep and flashing red led and it doesn't seem to let me config. I tried with 3 different tx/rx's and the closes i got was it ran for about 2mins once and that was it.
It works on the program card in as i can play with the values (now on default setting).
Any help ???
I recently got a used SP gt 2.0 LPF. coupled with a novak 13.5t. The problem i have is that there's no throttle, i tried configuring it but all i get is continuous beep.beep.beep and flashing red led and it doesn't seem to let me config. I tried with 3 different tx/rx's and the closes i got was it ran for about 2mins once and that was it.
It works on the program card in as i can play with the values (now on default setting).
Any help ???
01-30-2013 | 12:24 PM
hi all
I recently got a used SP gt 2.0 LPF. coupled with a novak 13.5t. The problem i have is that there's no throttle, i tried configuring it but all i get is continuous beep.beep.beep and flashing red led and it doesn't seem to let me config. I tried with 3 different tx/rx's and the closes i got was it ran for about 2mins once and that was it.
It works on the program card in as i can play with the values (now on default setting).
Any help ???
I recently got a used SP gt 2.0 LPF. coupled with a novak 13.5t. The problem i have is that there's no throttle, i tried configuring it but all i get is continuous beep.beep.beep and flashing red led and it doesn't seem to let me config. I tried with 3 different tx/rx's and the closes i got was it ran for about 2mins once and that was it.
It works on the program card in as i can play with the values (now on default setting).
Any help ???
Press and hold red button once for Neutral, Then you will hear 1 beep Second press and hold your full throttle while holding your full throttle hit the red button again. You should hear 2 beeps 3rd push your radio to full brake and hold hit red button again and you should hear 3 beeps. Turn everything off and see it that works.
If you cant get throttle to work or calibrate you may need to reverse the throttle on your radio
good luck
01-30-2013 | 12:31 PM
Tech Apprentice
iTrader: (1)
Joined: Nov 2011
Posts: 87
I used the procedure as on the manual.
1.transmitter on 2.hold down the set button(next to switch)3.turn esc on while holding down button until the led flashes.
When i do that, it flashes plus beeps as described. Throttle on neutral already and i should press the set button again, but nothing happens, red leds still flashing and beeping. Only way to stop it beeping is to turn it off
I used Carson reflex pro, etroniks pulse EX3 pro, Futaba 3PL
1.transmitter on 2.hold down the set button(next to switch)3.turn esc on while holding down button until the led flashes.
When i do that, it flashes plus beeps as described. Throttle on neutral already and i should press the set button again, but nothing happens, red leds still flashing and beeping. Only way to stop it beeping is to turn it off
I used Carson reflex pro, etroniks pulse EX3 pro, Futaba 3PL
01-30-2013 | 12:54 PM
Has anybody had any problems with their Revention Pro shutting off? My Revention Pro shuts off after just a few minutes during warm up prior to a race. I'll take my warm up laps, then pull off and wait to grid, and by the time the race is ready to grid, my car will be shut off. I have verified my settings and updated the firmware several times. The fan is operational and blowing down onto the ESC. I'm running a Team Epic D3 4.5 motor with 8.4 FDR. I have the Lipo cutoff set to no protection, and the over heat protection is disabled. I have temped the ESC and motor and they are both no hotter than 135-140F. The outdoor air temperature is no hotter than 60-70F I have the DMTS and DRRS set to middle of the road settings. I have since switched back to a Tekin RS Pro, and running with no problems. However, I'd like to find out what is the problem with my Revention Pro.
01-30-2013 | 02:15 PM
01-30-2013 | 02:41 PM
Tech Apprentice
iTrader: (1)
Joined: Nov 2011
Posts: 87
I used the procedure as on the manual.
1.transmitter on 2.hold down the set button(next to switch)3.turn esc on while holding down button until the led flashes.
When i do that, it flashes plus beeps as described. Throttle on neutral already and i should press the set button again, but nothing happens, red leds still flashing and beeping. Only way to stop it beeping is to turn it off
I used Carson reflex pro, etroniks pulse EX3 pro, Futaba 3PL
1.transmitter on 2.hold down the set button(next to switch)3.turn esc on while holding down button until the led flashes.
When i do that, it flashes plus beeps as described. Throttle on neutral already and i should press the set button again, but nothing happens, red leds still flashing and beeping. Only way to stop it beeping is to turn it off
I used Carson reflex pro, etroniks pulse EX3 pro, Futaba 3PL
I got it configured but the motor stutters and doesn't reach full revs, from the sound of it, its low revs on/0ff on/off stutter and not smooth
Is this the sensor wire knackered ??
01-30-2013 | 03:06 PM
Joined: Sep 2002
Posts: 9,295
From: Chicago Illinois USA
01-30-2013 | 03:08 PM
Joined: Sep 2002
Posts: 9,295
From: Chicago Illinois USA
Can you make sure your radio throttle EPA or other adjustment are in 100% default position..? Not 110% or 120% or 90%....must be 100%, and redo the whole calibration. And make sure after you are done with the 3 steps setup, you MUST turn off the ESC/Radio and turn back on to test...
01-30-2013 | 03:19 PM
Joined: Sep 2002
Posts: 9,295
From: Chicago Illinois USA
I can't tell you the 100% of boost = 100* of timing adding...not even 64* or 48*....far lower then that.