57LikesThe Speed Passion Thread
10-08-2012 | 10:54 AM
Tech Initiate
Joined: Oct 2012
Posts: 45
It is. I have removed/installed four times now. Following your instructions. Once I re-install and connect everything it just keeps popping up do you want to connect to your esc. I click obviously....yes. It pops back up again. I click yes.....It pops up again. I click no.... Read. Read ok. Do you want to connect to your esc.....Yes. wait for it........Do you want to connect to your esc. Yes.
I've tried holding down value to have it "Connecting to the PC"
I've tried holding down value to have it "Connecting to the PC"
Try This,
1. Uninstall V18 interface software
2. Uninstall anything that said SP, Reventon and SP lap under programs
3. Restart computer
4.Re-download V8 software
5.Install setup.exe
6. Install SpUsbInstaller.exe inside SpUsbDriver 6.6 folder
7. Make sure you say yes to everything windows ask you during install.
8. plug in the LCD card and got to Device manager, under ports it will shop Speed Passion Program Card(Com?)
9. unplug card and start interface software
10. At the main screen, hold the reset button on the lcd card and plugin the USB cable.
11. Update Firmware will show on middle left hand, update to V2.4.
12. Unplug after finish then replug.
13. Now connect ESC without BATTERY and any bare wire touching each other plus Cooling fan unpluged.
Thank you
10-08-2012 | 11:44 AM
Hello Nolan,
Try This,
1. Uninstall V18 interface software-Done
2. Uninstall anything that said SP, Reventon and SP lap under programs--Done
3. Restart computer--Did full reboot from last know good settings per windows
4.Re-download V8 software--Done
5.Install setup.exe--Done
6. Install SpUsbInstaller.exe inside SpUsbDriver 6.6 folder--Done
7. Make sure you say yes to everything windows ask you during install.--Always
8. plug in the LCD card and got to Device manager, under ports it will shop Speed Passion Program Card(Com?)--Com3
9. unplug card and start interface software---Done
10. At the main screen, hold the reset button on the lcd card and plugin the USB cable.---Done
11. Update Firmware will show on middle left hand, update to V2.4.---Yup
12. Unplug after finish then replug.---In Process
13. Now connect ESC without BATTERY and any bare wire touching each other plus Cooling fan unpluged.---In Process
Thank you
Try This,
1. Uninstall V18 interface software-Done
2. Uninstall anything that said SP, Reventon and SP lap under programs--Done
3. Restart computer--Did full reboot from last know good settings per windows
4.Re-download V8 software--Done
5.Install setup.exe--Done
6. Install SpUsbInstaller.exe inside SpUsbDriver 6.6 folder--Done
7. Make sure you say yes to everything windows ask you during install.--Always
8. plug in the LCD card and got to Device manager, under ports it will shop Speed Passion Program Card(Com?)--Com3
9. unplug card and start interface software---Done
10. At the main screen, hold the reset button on the lcd card and plugin the USB cable.---Done
11. Update Firmware will show on middle left hand, update to V2.4.---Yup
12. Unplug after finish then replug.---In Process
13. Now connect ESC without BATTERY and any bare wire touching each other plus Cooling fan unpluged.---In Process
Thank you
10-08-2012 | 12:32 PM
Hello Nolan,
Try This,
1. Uninstall V18 interface software
2. Uninstall anything that said SP, Reventon and SP lap under programs
3. Restart computer
4.Re-download V8 software
5.Install setup.exe
6. Install SpUsbInstaller.exe inside SpUsbDriver 6.6 folder
7. Make sure you say yes to everything windows ask you during install.
8. plug in the LCD card and got to Device manager, under ports it will shop Speed Passion Program Card(Com?)
9. unplug card and start interface software
10. At the main screen, hold the reset button on the lcd card and plugin the USB cable.
11. Update Firmware will show on middle left hand, update to V2.4.
12. Unplug after finish then replug.
13. Now connect ESC without BATTERY and any bare wire touching each other plus Cooling fan unpluged.
Thank you
Try This,
1. Uninstall V18 interface software
2. Uninstall anything that said SP, Reventon and SP lap under programs
3. Restart computer
4.Re-download V8 software
5.Install setup.exe
6. Install SpUsbInstaller.exe inside SpUsbDriver 6.6 folder
7. Make sure you say yes to everything windows ask you during install.
8. plug in the LCD card and got to Device manager, under ports it will shop Speed Passion Program Card(Com?)
9. unplug card and start interface software
10. At the main screen, hold the reset button on the lcd card and plugin the USB cable.
11. Update Firmware will show on middle left hand, update to V2.4.
12. Unplug after finish then replug.
13. Now connect ESC without BATTERY and any bare wire touching each other plus Cooling fan unpluged.
Thank you
No Luck.
10-08-2012 | 01:58 PM
Tech Apprentice
Joined: Oct 2012
Posts: 70
No specific time on when ROAR approval will be given or how long the process will take.
Nolan,
Are you still experiencing issues? If so can you post the specs of you computer? Window XP, 7.0, other?
Thank you.
10-08-2012 | 02:31 PM
i had the same issue with another laptop and i went under device manager with the card plugged in, clicked on it on the device manager then it gave me the choice to reinstall drivers i did and it works just fine now, i had to do it twice
10-08-2012 | 02:58 PM
Joined: Feb 2009
Posts: 3,228
From: Fort Wayne, IN
10-08-2012 | 03:29 PM
10-08-2012 | 04:24 PM
Yup. I know I am waiting for someone...hint hint. To make a Mac program. I know for a fact I would have never been in this issue. My Mac doesn't crash or have program's freeze...but thats a whole new forum altogether. I guess I gotta track down Davitto or someone local to load up Stock0.
10-08-2012 | 06:43 PM
Tech Master
Joined: Jan 2005
Posts: 1,457
Hope you have time to answer my PM 
SP Tech and Sptech1 are the official Speed Passion USA support here in Rctech. Any question about our products, orders or anything....They will be here to answer. And myself will help to answer as well (I do need help, I can't answer 20-30 PM plus email everyday anymore)....
10-08-2012 | 06:59 PM
Tech Apprentice
Joined: Oct 2012
Posts: 70
Yup. I know I am waiting for someone...hint hint. To make a Mac program. I know for a fact I would have never been in this issue. My Mac doesn't crash or have program's freeze...but thats a whole new forum altogether. I guess I gotta track down Davitto or someone local to load up Stock0.