R/C Tech Forums - Search Results
R/C Tech Forums

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Wiki Posts
Calendar
Today's Posts
Search
Vendor Directory
 
Page 1 of 20
1
2
3
11
Last »
Search: Posts Made By: trilerian
Showing results 1 to 25 of 500
Search took 0.06 seconds.
Forum: Radio and Electronics
Yesterday, 10:41 PM
Replies: 534
Views: 187,803
Posted By trilerian

You should still be able to get close to 30A with...

You should still be able to get close to 30A with the 5 1ohm resistors. I just wired up a discharge bank in series to my 308 and was able to get 26-27A with a bank of 5 1ohm resistors. The way the...
Forum: Radio and Electronics
Yesterday, 07:40 AM
Replies: 4
Views: 199
Posted By trilerian

As stated above it shouldn't make a difference...

As stated above it shouldn't make a difference while charging. But for an IR check, yes, you can just connect the sensor lead to the positive side on the battery. DRC sells a 1s/2s switch and its...
Forum: Radio and Electronics
04-25-2024, 07:42 AM
Replies: 163
Views: 34,289
Posted By trilerian

Do you tell the program the update time or does...

Do you tell the program the update time or does it take it from the timestamps of the readings?
If you are telling it the update time then this:
if((currentTime - lastUpdateTime) >...
Forum: Radio and Electronics
04-23-2024, 02:57 PM
Replies: 163
Views: 34,289
Posted By trilerian

How big is your encoder wheel? I can print one...

How big is your encoder wheel? I can print one in PETG, or even PA6-GF. Haven't had a chance to print with the PA6 yet, but it is supposed to be dimensionally stable.

Would you care to share...
Forum: Radio and Electronics
04-22-2024, 06:30 PM
Replies: 163
Views: 34,289
Posted By trilerian

Your angular velocity will be the same no matter...

Your angular velocity will be the same no matter where you are on the disc. Linear velocity will change, but that will not matter.
Do you have any gear reduction at all in the setup? 15ms is...
Forum: Radio and Electronics
04-21-2024, 06:27 PM
Replies: 163
Views: 34,289
Posted By trilerian

In a couple more weeks I should have some time...

In a couple more weeks I should have some time available to look into this as well. I have a bunch of different dev boards that can be tried. I can use the MiniPro flywheel and base for the...
Forum: Electric On-Road
04-20-2024, 11:10 PM
Replies: 6,823
Views: 2,054,279
Posted By trilerian

I use a body reamer. I start with a hobby knife...

I use a body reamer. I start with a hobby knife to mark the spot, and then use the reamer.
Forum: Radio and Electronics
04-18-2024, 09:29 AM
Replies: 534
Views: 187,803
Posted By trilerian

While Roelof post will definitely get you to some...

While Roelof post will definitely get you to some usable values, personally I would use 5 x 0R5 (0.5 ohm) 100W resistors. You can get away with 50W, but the 100W will stay quite a bit cooler and...
Forum: Radio and Electronics
04-18-2024, 05:12 AM
Replies: 534
Views: 187,803
Posted By trilerian

If you want to, you just wire the positive of the...

If you want to, you just wire the positive of the fan between the battery positive and the resistor bank, then the negative to the negative. However doing this you are only going to get 3.2-4.2V for...
Forum: Radio and Electronics
04-17-2024, 09:50 PM
Replies: 534
Views: 187,803
Posted By trilerian

Parallel will look like train tracks. Line the...

Parallel will look like train tracks. Line the resistors up longitudinally adjacent and run a wire down both ends. Series would be your old school string of Christmas lights.

But in this case you...
Forum: Radio and Electronics
04-17-2024, 05:16 AM
Replies: 143
Views: 20,280
Posted By trilerian

There are way too many caveats to say that amps...

There are way too many caveats to say that amps and torque are directly proportional. There is a correlation between startup amps and startup torque but it is dependent on other variables as well....
Forum: Radio and Electronics
04-16-2024, 08:21 AM
Replies: 163
Views: 34,289
Posted By trilerian

Did you use the first sketch you posted, the...

Did you use the first sketch you posted, the original from Simple Dyno? Can you get the info using a terminal emulator instead of Simple Dyno? With the IDE open and a USB connected can you see the...
Forum: Electric On-Road
04-16-2024, 07:11 AM
Replies: 6,823
Views: 2,054,279
Posted By trilerian

I'm not sure the tiniest of drops is good enough....

I'm not sure the tiniest of drops is good enough. The other guy I was running with used blue Loctite paste and one of his came apart in the main.

Regardless, I'm going back to the old versions...
Forum: Electric On-Road
04-15-2024, 04:07 PM
Replies: 6,823
Views: 2,054,279
Posted By trilerian

Call it OCD if you want, I don't have a rational...

Call it OCD if you want, I don't have a rational explanation. Well, I do, but not one most likely accepted by the masses.
Forum: Radio and Electronics
04-15-2024, 02:08 PM
Replies: 163
Views: 34,289
Posted By trilerian

The Nano's ADC is extremely linear. As said, its...

The Nano's ADC is extremely linear. As said, its resolution being 10bit isn't good, but you can oversample it. The ADC on the Nano is ~10000 samples / sec. For the Minima, I can create a simple...
Forum: Radio and Electronics
04-15-2024, 11:27 AM
Replies: 163
Views: 34,289
Posted By trilerian

The ADC on the 328P is actually quite good...

The ADC on the 328P is actually quite good despite the resolution. Which we both know we can oversample it pretty easily for that resolution. Generally I have found that even over sampling the 328P...
Forum: Electric On-Road
04-15-2024, 09:13 AM
Replies: 6,823
Views: 2,054,279
Posted By trilerian

I hate using Locktite or thread locker. ...

I hate using Locktite or thread locker. Generally I am able to get away with not using it. Never used it anywhere on any of my previous Awesomatix kits, don't use it on my off road kits. Was...
Forum: Electric On-Road
04-15-2024, 07:39 AM
Replies: 6,823
Views: 2,054,279
Posted By trilerian

My maiden voyage out with my 800R was not so...

My maiden voyage out with my 800R was not so good. Mainly the issues can be boiled down to the front drive shafts. Without doubt this part needs to be put together with Loctite. I thought I read...
Forum: Electric On-Road
04-12-2024, 10:52 AM
Replies: 6,823
Views: 2,054,279
Posted By trilerian

Does this mean only one end of the car can be a...

Does this mean only one end of the car can be a deep roller? I clicked the link and I'm like, why am I getting an add for Silence of the Lambs?
Forum: Radio and Electronics
04-12-2024, 07:29 AM
Replies: 160
Views: 33,814
Posted By trilerian

Actually, higher current ESCs generally tend to...

Actually, higher current ESCs generally tend to have mosfets with lower RDS on resistance and will parallel more of these on the pcb than lower amperage ESCs. For example the Hobbywing just stock...
Forum: Radio and Electronics
04-11-2024, 08:12 PM
Replies: 63
Views: 40,187
Posted By trilerian

I agree with that. But what fun is a stock motor...

I agree with that. But what fun is a stock motor on a track that allows for that?
Forum: Electric On-Road
04-11-2024, 08:09 PM
Replies: 6,823
Views: 2,054,279
Posted By trilerian

Supposed to make the car "lazy", going to roll...

Supposed to make the car "lazy", going to roll deeper and be less responsive. I am running on asphalt and have never ran on asphalt before. I've got short links ready to change out if need be....
Forum: Radio and Electronics
04-11-2024, 05:45 PM
Replies: 163
Views: 34,289
Posted By trilerian

Actually what I think @PDR is suggesting would...

Actually what I think @PDR is suggesting would allow you to offload your data every 50Hz so you can clear your array and save memory. You wouldn't be recording at 50Hz, just offloading. Most likely...
Forum: Radio and Electronics
04-11-2024, 04:48 PM
Replies: 163
Views: 34,289
Posted By trilerian

Do you have the R4 (Minima)? You should be able...

Do you have the R4 (Minima)? You should be able to just port the code over. That is one of the good things about Arduino. The pinout on it should be the same as the Nano.
Forum: Radio and Electronics
04-11-2024, 12:38 PM
Replies: 63
Views: 40,187
Posted By trilerian

I normally setup the X axis for RPM, I just did a...

I normally setup the X axis for RPM, I just did a quick run to post the Time Vs RPM and added the other 2 graphs. I actually don't use the dyno that much anymore as I am running mod now, when I get a...
Showing results 1 to 25 of 500
 
Page 1 of 20
1
2
3
11
Last »


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.