|
Ripmax 2S1P 7.4V 2800mAh TX Li-Po (Futaba)
Ripmax - Futaba T4PX Spares Li-Po Charger 500mA Ripmax Tx (Futaba) Li-Po Charger 500mA, 8.4V EURO 14SG/FX22/FX32 (P-FBC100/EUR) - Ripmax Ltd |
Originally Posted by gardey
(Post 14958025)
I've selected FASST 2.4 in receiver selection & followed procedures as instructed. The receiver stays red.I push the receiver button & it flashes red .then stays red.
- If you aren't in the display mode go to the Receiver screen and select a different Rx and turn off the Tx. Then turn on the Rx first (it should flash red). Next turn on the Tx. Go to the Receiver screen and reselect the Fasst Rx. See if it ask you about the failsafe. If it does select "yes/agree/accept" (whichever one it offers). The Rx should go flashing green if I remember correctly. Now hold the Tx right next to the Rx and press the Rx bind button. The Rx led should go to solid green. If this doesn't work I would contact Futaba. |
Originally Posted by gardey
(Post 14958033)
If you purchase a Futaba in Australia beware that you will get no support from anyone in the U.S. or Australia.
I would not recommend Futaba after my recent experiences trying to get help. The wholesales dealer in W.A.apparently expects that all buyers to investigate the dealers to ascertain the origin of the products' importation. They won't assist at all. U.S. were slightly better but won't answer the support line & if you're from overseas , again, it's not their problem. Sanwa next time for me I think. |
Originally Posted by darnold
(Post 14958523)
I'm really surprised that this is happening. Maybe an e-mail to Futaba Japan pertaining to the poor customer service within their distribution chain is in order. I would also let them know what service you need from them and ask them where you can send it to for service.
|
Rec
Is anyone using the 204 that has no antenna or what is the smallest rec to use
|
The R204, R304 and R614 all have the same case and size (1.38 x 0.91 x 0.33 in). I have yet to see a smaller Futaba Rx that use Fasst and FHSS.
|
gardey- Did your Fasst 416FF ever bind with your 4Px?
|
Originally Posted by darnold
(Post 14961615)
gardey- Did your Fasst 416FF ever bind with your 4Px?
|
Originally Posted by darnold
(Post 14961615)
gardey- Did your Fasst 416FF ever bind with your 4Px?
|
Originally Posted by darnold
(Post 14957129)
It should work fine I believe. My 614E worked with no problem.
Therefore, assuming power is being given to the rx, :lol:, then I would check the following: 1) Fasst rx setting is selected under "Receiver" within the Tx menu and leave your Tx on at this menu. 2) When you turn on the Rx it should start flashing green. 3) When/If you get a message on your Tx asking you about resetting any failsafe say "Yes/Accept". Your Rx should bind and the LED should turn solid green. What is yours doing? |
Originally Posted by gardey
(Post 14962099)
No.No support yet.Futaba tell me to contact RC Wholesale in W.A.& I'm waiting for a call tomorrow from someone who may be able to help me.The whole experience has been a nightmare. My Australian supplier didn't buy it through the aus wholesaler so nobody wants to help me sort it out.still waiting. You would think Futaba could tell me how to sort it?
As far as your Australia distributor: It sounds like they got a deal through indirect channels and made you pay full price so that they made more money? |
Yep.he said the wholesaler won't supply him because he doesn't have a shopfront? Supplier denied thatn He says, she says politics doesn't help us as the end consumer.just bad for Futaba.Sanwa for me next time & hope they have better back up than Futaba...couldn't be worse
. |
So it turned out the 614 wont link with the 4px.so the expert told me today. Reckoned it's a different 4px from another country so the receiver wont recognize it.Ripped off.had to by new receivers after all.wasted my money & should have got a 4pv about half price or a Sanwa m12.Futaba sux
|
What does being from a different country have to do with binding to a fasst rx? Id be asking for a refund from whoever you bought it from and go with a 4pv.
|
I have 614 bound to my 4PX....
R614FF-E, more than one also the USA dist says it works: TowerHobbies.com | Parts Compatibility: Futaba R614FF-E 4-Channel FASST Receiver 4PK/4PKS |
| All times are GMT -7. It is currently 10:51 AM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.