HOBBYWING TECH SUPPORT 1/8 & 1/10 OFF ROAD
Are you using the right port to plug into
Tech Champion
iTrader: (4)
It sounds like you may need to start a Repair Authorization or R.A form with Hobbywing USA. Go to their site to start the process. Im sorry to hear that you are havi g an issue.
Sorry but I am thinking the led box is done. I have had my box for years and it never did that.you may have got a bad one.it happens sometimes hope the r a will get you a new one.
Tech Regular
iTrader: (3)
You're most likely going to need the 1/8 set up, maybe the https://www.hobbywingdirect.com/prod...nt=11823665092
Slevin, I would stick with the 1600 kv combo if you plan on running 6s.
Tech Master
iTrader: (6)
Hey , sorry..... does anyone know if an Orion program box for the R10 pro works on the hobbywing V3 120amp?
I don’t think it will different software
Tech Adept
Throttle during steering
I have a xr8 sct that I just purchased. The issue I am having is when I do multiple steering inputs on the bench the throttle will also go. It is almost like a glitch. I have tried recalibrating and this does not work. Any suggestions. It is paired with a tekin pro 4 4300 motor.
set all you radio end points, set your neutral range on the esc at 6% save it then re calibrate radio to esc .
Tech Addict
iTrader: (16)
Raced my 2wd drive buggy for first time in while tonight. Was having some issues after a tumble or hard hit .Buggy would like lose power, servo still worked, but car would not move for a second or two. I thought bad sensor connection. I pulled sensor wire from motor and motor still worked so I decided to race sans wire. The issue still happened in main. Equipment: sanwa rx 482, xr10 Pro, reedy mach 2 8.5t, fantom 4000 battery, savox 1257.
Any ideas? Haven't had time to tear into. Will make sure all solder connections are good.
Any ideas? Haven't had time to tear into. Will make sure all solder connections are good.
Tech Initiate
Hy Adim X!
How did you put the sanwa rx482 receiver into the car?
This type of receiver has to be set correctly into the car as it's manual says. Otherwise it can cause radio range problem...
You said the car stopped for a few second, then start. It sound more a range issue than a ESC probelm.
Try to clean out the receiver, and make sure that it is stays on the chassis instead of laying down.
I hope that will solve your problem!
How did you put the sanwa rx482 receiver into the car?
This type of receiver has to be set correctly into the car as it's manual says. Otherwise it can cause radio range problem...
You said the car stopped for a few second, then start. It sound more a range issue than a ESC probelm.
Try to clean out the receiver, and make sure that it is stays on the chassis instead of laying down.
I hope that will solve your problem!
Tech Addict
iTrader: (11)
Hi All,
Got an XR8 Plus hooked to HW 2250 KV motor. I am getting low end cogging, if the motor starts from a dead stop it cogs. If the motor is spinning it is fine, super smooth all the way. It is just on initial startup.
I tried two different sensor wires. Same result with both.
I pulled the sensor wire and the problem stopped. Can I run it without the sensor wire?
Default config, I decreased punch to 4 and that did not work, I put the punch to 9 and that did not work.
Any help would be appreciated.
Got an XR8 Plus hooked to HW 2250 KV motor. I am getting low end cogging, if the motor starts from a dead stop it cogs. If the motor is spinning it is fine, super smooth all the way. It is just on initial startup.
I tried two different sensor wires. Same result with both.
I pulled the sensor wire and the problem stopped. Can I run it without the sensor wire?
Default config, I decreased punch to 4 and that did not work, I put the punch to 9 and that did not work.
Any help would be appreciated.
Last edited by cryofix; 08-22-2018 at 07:22 PM. Reason: typo
Tech Champion
iTrader: (4)
You can run it with no sensor wire, it will actually feel softer on t by e bottom end and should require more throttla input. Is the 3250 you have one ofvtge new series or an old one? The new ones have solder tabs.
Tech Addict
iTrader: (11)
Rma turn around
What's the average turn around for RMA? Got a xr8 plus flashing green four times