Do you mean what motors I'm using?

I have a Speedzone 5.0, Team Powers 17.5, and Trinity D3.5 17.5

Slightly off topic

Can anyone advise the bearing size for the HW 21.5 motor?
Thanks

hi guys,

Can the extreme stock 60amp esc be updated with the latest blinky software?

Hope you can advise

Was checking the ROAR approved motor list tonight. Found the modified V10 3.5t,4.5t,5.5t,6.5,7.5 and 8.5t motors listed. Cannot find the higher turn motors listed. Are they not ROAR legal?

Yes, but the approvals are in the ROAR forum(s):

10.5: http://roarracing.org/4rmb/showthrea...ck-30401020046
13.5: http://roarracing.org/4rmb/showthrea...ck-30401020047
17.5: http://roarracing.org/4rmb/showthrea...ck-30401020048
21.5: http://roarracing.org/4rmb/showthrea...ck-30401020049

etc, etc.

Phil.

Hi guys,
Having issues running hobbywing v3.43 on my new laptop. no matter how i open it it brings up the same message.
Device cannot be opened
run as admin or normal
any help would be appreciated

Hi guys,
Having issues running hobbywing v3.43 on my new laptop. no matter how i open it it brings up the same message.
Device cannot be opened
run as admin or normal
any help would be appreciated

hi guys, any suggestions on a FDR for 10.5 boosted

thx

Hey Guys
I am running a 3.1 1s speedo on my 12th pan car running blinky software and am finding I have a small delay when starting a race, not so noticable in a stagger start qualifier but last sunday in the final I was nearly taken out by the guy who started behind me on the grid. It ok when running well at least i am not consious of a delay then.
Any ideas.

I am assuming you are using windows 8.1? If not a little more info about the computer might be helpful. If running as admin does not work try running it in compatibility mode.
right click on program - > select Properties -> Compatibility Tab -> select check box "Run this program in compatibility mode for:" then in the drop down box select windows xp. Click Ok to apply these settings. See if this works.
If not try uninstalling and reinstalling. Could be a driver issue.

Also if you are connecting to the ESC don't forget you need to have the device plugged into a battery and switch on.

Also was the previous version of the software working?

Delay usually indicates controller is running in sensorless mode. So check your sensor wire. If this is not the problem then try re-calibrating the ESC to the radio. Could also change your deadband to the lowest setting although if you are just hesitating at start then it probably a sensor issue. If the cable doesn't help then check the sensor board on the motor. I have had both go bad before and you get the delayed start feeling.

So is replacement the only way to test a sensor board? Have treid recalibration and a new cable. Could it be armature spacing??

If you haven't opened the motor for maintenance it should be fine.
If you did and the shims ar in the wrong place it could happen that sensor signal is weak and therefore the problems.
Most of the time it is a sensor cable or port on motor or esc if the motor hasn't been openend.

Regards Roy

Hi Guys,

I have Xerun 60A v2 esc and Speedpassion LCD Professional Program Card.

Would like to load software for Blinky, what version should I download? I see a lot (e.g. v1.62, v1.63, v1.64, etc)

Many thanks.

Joel

Download the latest v3.43 that will have the software blinky mode that you need but if you esc has sp software on it and so does the lcd you will not be able to do it .You will need to send me an email at [email protected] so i can send you some different files so it can work.