|
Wiring/troubleshooting help ??
I’ve wired up 2 different brand new tekin rs pro black editions , to 3 different used Sanwa 493’s and a 1up racing fh5 receiver , all 4 don’t power up and both of the tekin esc’s were blinking all lights simultaneously! 4 bad receivers ?? I don’t think it’s a cold solder joint , so what am I missing ??
|
Originally Posted by lbsnoopy
(Post 16227092)
I’ve wired up 2 different brand new tekin rs pro black editions , to 3 different used Sanwa 493’s and a 1up racing fh5 receiver , all 4 don’t power up and both of the tekin esc’s were blinking all lights simultaneously! 4 bad receivers ?? I don’t think it’s a cold solder joint , so what am I missing ??
|
411
Originally Posted by gigaplex
(Post 16227096)
What does a multimeter tell you about the BEC output voltage on the ESC's receiver plug?
|
411
Changed the esc setting to 7.4 and it’s putting out 7.99 . Where do I look now ??
|
Steerservo is working? If not try to rebind the receivers.
And did you calibrate the ESC's? As AI expleins: A Tekin ESC with all lights blinking often indicates a short in the motor or ESC, a lack of sensor input, or a calibration issue. To troubleshoot, check for a short between motor wires B and C, perform a radio calibration, ensure proper transmitter and receiver binding, and try a different motor. If the problem persists, the ESC may be damaged. |
Originally Posted by lbsnoopy
(Post 16227099)
Getting 5.95 v , I have the esc set at 6.0v.
|
Originally Posted by gigaplex
(Post 16227105)
If it's giving the correct power out then the receivers should be powering up. Are you sure they're plugged in correctly?
|
Not sure I remember correctly, but I think when the receivers are no yet bound to the radio, he light stays out (I could be wrong about this, though). Have you tried going to the binding procedure nonetheless?
|
Reply
Originally Posted by DirkW
(Post 16227115)
Not sure I remember correctly, but I think when the receivers are no yet bound to the radio, he light stays out (I could be wrong about this, though). Have you tried going to the binding procedure nonetheless?
|
Originally Posted by lbsnoopy
(Post 16227157)
can’t bind , no power was going to the receiver , so , I opened up a new gen3 stock spec , wired it up and connected it to all 4 of the receivers and I had power , the car is a go . Just my luck , 2 rs pro be’s , 1 from tekin and one from a eBay distributor, both bad .
|
Reply
Originally Posted by hunterdawg
(Post 16227185)
Send to Tekin for repair.
|
Originally Posted by lbsnoopy
(Post 16227157)
can’t bind , no power was going to the receiver , so , I opened up a new gen3 stock spec , wired it up and connected it to all 4 of the receivers and I had power , the car is a go . Just my luck , 2 rs pro be’s , 1 from tekin and one from a eBay distributor, both bad .
|
Teply
https://cimg0.ibsrv.net/gimg/www.rct...82ba2e849b.jpg
Checked positive and negative here . https://cimg0.ibsrv.net/gimg/www.rct...561addf9a3.jpg 1 up fh5 receiver installed with the spec esc |
Esc’s
https://cimg7.ibsrv.net/gimg/www.rct...9212d402a0.jpg
Connectors are good on both . Both are brand new . Just got the one on Friday from tekin. |
411
Every one of my tc’s has this 13.5 setup with the rs pro black edition, except for one that is mod . The only thing I can figure is the esc’s !?
|
| All times are GMT -7. It is currently 01:12 PM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.