Novarossi engines thread
#3751
Tech Rookie
anyone know where to get gd deal for this 2 size of bearing?
7x19x5
14.5x26x6
*if initially the front engine bearing is 5mm in width, will there be any effect if i replace it with a 6mm width instead?
Thanks
7x19x5
14.5x26x6
*if initially the front engine bearing is 5mm in width, will there be any effect if i replace it with a 6mm width instead?
Thanks
#3753
Tech Regular
listen guys.. my car just got ran over by a real car lol.. it was a 710 with a megen x-12 so it was a nova engine.. i wanna get the 733 with a novarossi engine. what should i get i want great power.. want to spend around $300 give or take a little..
i want durability and want to make sure they last as well as be a monster
i see these flash engines for $600+.. what does it mean when the engines is flash
i want durability and want to make sure they last as well as be a monster
i see these flash engines for $600+.. what does it mean when the engines is flash
#3754
guys i want to make a question.
ehich engine will you buy?
the first cordoba edition in that set(pipe 3 plugs etc)
or the max mx 21 max xl9 tq?
and why?
ehich engine will you buy?
the first cordoba edition in that set(pipe 3 plugs etc)
or the max mx 21 max xl9 tq?
and why?
#3755
I would go with the max xl9 tq it will have a little bit more power and better runtime being it is fully modded!!!!! The 35+21 have been none to hold up longer then the max .21s FYI.
#3756
the problems with the worn pistons in the exhaust side that some guys had with the cordobas is user's error or what?has anyone had any problem with the smaller crank pin?
#3757
I had a 35 + 21 do it. I think it comes from leaning it out too soon. You really need to break these tight ones in a LONG time and VERY gingerly.
#3758
Tech Elite
iTrader: (13)
Join Date: Feb 2007
Location: Landsborough, Queensland, Australia.
Posts: 2,142
Trader Rating: 13 (100%+)
Novarossi RER .12 Turbo engine
Does anyone know what a Novarossi RER .12 Turbo engine is, or where I can find the specifications for one?
Kindest regards,
Lars.
Kindest regards,
Lars.
#3759
#3760
Tech Regular
http://www.novarossi.it/eng/products...display=public
#3761
Get the latest Collari. It has the large crank pin and R7 rod plus the new long crank.
http://www.novarossi.it/eng/products...display=public
http://www.novarossi.it/eng/products...display=public
Where can I get the crank for this engine
#3762
Tech Fanatic
iTrader: (17)
hi guys, i have a n12t1 and when i spin the flywheel with my hand i can feel its abit loose and is notchy when i get to a certain position, i suspect the bearings are shot, had a few flame outs while running which i've never had before.
does anyone know what size the bearings are? and wheres a good place to get them?
or i should just bin this cheapo motor and go for something abit better?
motor still has good pinch though.
thanks.
does anyone know what size the bearings are? and wheres a good place to get them?
or i should just bin this cheapo motor and go for something abit better?
motor still has good pinch though.
thanks.
#3763
Tech Elite
iTrader: (15)
kai .. it should spin free and be notchy when the piston is at the top dead centre this is called pinch and its how we measure its compression.
how old is the engine?
how many litres of fuel have you put through it?
do the bearings feel notchy when you turn the crank slowly?
it could be a case of bad o rings in the carb? if so i have spare novarossi carbs from the updated 353 series engines you could try
how old is the engine?
how many litres of fuel have you put through it?
do the bearings feel notchy when you turn the crank slowly?
it could be a case of bad o rings in the carb? if so i have spare novarossi carbs from the updated 353 series engines you could try
#3764
Tech Fanatic
iTrader: (17)
kai .. it should spin free and be notchy when the piston is at the top dead centre this is called pinch and its how we measure its compression.
how old is the engine?
how many litres of fuel have you put through it?
do the bearings feel notchy when you turn the crank slowly?
it could be a case of bad o rings in the carb? if so i have spare novarossi carbs from the updated 353 series engines you could try
how old is the engine?
how many litres of fuel have you put through it?
do the bearings feel notchy when you turn the crank slowly?
it could be a case of bad o rings in the carb? if so i have spare novarossi carbs from the updated 353 series engines you could try
the motor is 9 meetings old, 5 by me and 4 from the previous owner, its been thrashed so i'm just guestimating around 10L or so.
yeah i think i know what you mean by the pinch, it makes that pop sound right?
when i turn the crank slowly, about halfway between top dead centre and bottom dead centre is where i'm feeling it is notchy, also the crank has abit of play from side to side parallel to the face of the bearing.
i'll rip the carb apart tonight and see if i've got any bad orings.
thanks mate.