No, we do not coat cranks at this time.

Regards,
Lance

I had a bunch of questions about If you can send in a complete engine Assembled, for a resize and bearing replacement. And Yes if you are having bearings replaced and a resize that is fine to send in the whole engine. I will clean it, resize it and replace bearings and re-assemble it.

Thanks guys,
Lance

Jeremiah, received your payment. I will notify you as soon as I receive your piston/sleeve and e-mail you a usps priority tracking number when it ships.

Thanks so much for your business!

lance

Gary,Steve and Josh got your orders this morning and shipped out today usps priority and E-mailed you tracking numbers. Thanks guys


Lance

Rececntly we were hanging out the dust bowl Rev and I met Lance from RC RENEW and I thank the man upstairs for it we race at Rev and its usually never watered and we all know that this is hard on equipment motors especially .Lance hooked me up and serviced my motor for pennies I really am just a above average driver in my own mind and love tie-ing the shoes of a lazy turn marshall ,so thanks for the hook up and im telling you all if you need it done right call Lance his crew gets it done . Hey Dana water that thing !!!!
just thought I wold throw a little non rc eye candy!!

Well hopefully my p/s get to him tomorrow so I can get it back quickly Should be there tomorrow/ tue... praying it gets to me before the weekend...

Jerry

Jerry, I received you P/S today and shipped it out today. You should have it by wed or Thurs. So that should give you enough time to get it broke in for racing this weekend! I e-mailed you tracking.

Thanks so much for your business, it is appreciated.

Best Regards,
Lance

Awesome, you the man, will have a B5 and Reedy your way soon

I just wanted to say good job to all my fellow racers at Revelation raceway where Saturday night at the Monster energy series. A lot of my friends and customers were tearing it up With engines that we resized and serviced. Its nice to see your hard work paying off! See you guys at the final race of the series!!

Take care,
Lance
Rcrenew.com

whats up lance, its trevor with the werks b7, i can pick it up at the next monster race because i wont be there this weekend:

Hey Trevor! No problem, I got it ready to go for you. I will bring it to the next Monster race. Thanks again and see you out there!

Lance

Hey Guys, Update on orders: Erice your B5 is good to go with ceramics and a resize, Sean Your ninja resize is done, tom your speed ceramics and resize is done and all shipped today.

Thanks,

Lance

Order update: Nick, repaired the Ninja piston and sleeve that you just had resized by someone else. Just goes to show, not all resize services are quality out there. BE careful who you send your stuff to guys.

Brett, got your 2 speed resizes finished

Joey, your sirio is finished ith new ceramics

Trevor , your extech is resized

Ed, repaired your speed piston sleeve that another service over pinched.

Thank guys! your tracking numbers have been E-Mailed to you.

See you at the races!!

Lance i was @ Revs last night and Nick told me about someone who resized his sleeve and it was oval and tweeked You took that guys mess and pinched it the way it should have beed done....good job man

Thanks, Resizing these engines is no joke. There are a lot of people who do it out there but not a lot of people who do it right. The attention to detail and equipment used plays a big part of it. But also Technique. I am a master tech on "real" engines so I know a lot about what it takes to make an engine run at its best. WE have changed a lot of peoples minds that we race with about resizing. They too had a lot of bad experiences with other services. And they gave us a shot and were amazed. Thats actually why we started this business. AS we ourselves were not happy with the services we tried either. So WE started doing it for ourselves as racers, Doing it our way, Resizing in 3 stages, not just one, with tolerances so close it allows for a precise fit without over "pinching" and we wanted a short easy break in with a factory taper, Not a super tight single pinch that is tight to far down the sleeve and that takes forever to loosen up and beat's up you internals. then our friends and fellow racers used our services, and it grew from there.There are a couple guys out there who do a good job. So do your research before you ship off your Expensive engine to someone. WE have done hundreds of engines will all positive feedback so far. and repaired a lot "especially lately" that were messed up by other people.


Thanks see you guys next week at the final Monster race!!!!

Lance