I have an order going together right now.... I would expect them in ~10 days or so depending on the customs nazi's :)

Not sure who you spoke with but AbsoluteHobbyz has more than 20 of these in stock.

We will offer the engines on the site to retail consumers soon, didnt want to initially, to support the dealers, but its a crazy time in the RC industry lately and might be the best move so customers have a good supply of product.

Now te B01T has been out for a while, how does it compare to the B01 in regards to low end, top, runtime, etc?

well i got a very good chance to run the bo1 and to1

bo1 was good all day finally broke in at the 2 gallon mark.... motor temps where 200-210 all day.. was consistant 10.30 to with a 7mm restrictor in buggy.. odonnell fuel.. 1.1 clutch ( which a 1.0 will be put in for next race) with aluminum 3 shoe clutch.. very smooth nice usable power band no complaints here on this motor...

to1 was good all day but still has a bit to go before it gets broke in.. have around 1.5 gallons on it and still has crazy pinch.. even without the plug in it will stop by the pinch... was geting 11 mins easy with a tad left in the tank in the truggy.. motor temps never seen over 200* all day.. crazy crazy power out of this mill... we had this 1 jump right off a corner and the buggys could just make it.. very few truggy where making it but i had no problems all day with it... qualified 4th in the "a' and we took off.. got to the lead by lap 3.. started to pull away from the pack and yup around lap 10-11 the worst thing possible happend.. a lapped car missed a jump and landed in the straightaway... well going full wood down the straight i hit him head on.. ripped the hole left side of the truck off.. left front arm, left rear arm, exhaust got removed and wing broke... and ya know the kicker... that truck drove away from the blast..... thank to tony and rody for thess great engines... got alot of questions on the motors.. this will be the must have engine in truggy this summer.. the best of the best in my eyes.. bottom of a .25-.28 and the rpm's of the .21's.. this motor is hands down better than the c6 he made years ago... thank you again.. jeremy

Thanks for your reply Jeremy. That must have been one hell of a crash!

Sounds like the B01T is a step up from the B01 in the power department.

maxbashing.com/mbforum/showthread.php?t=12303

here we go, ran the B01T yesterday and was awesome

Thanks for the posts Jeremy and RJ...

I like this one from RJ :nod::D

"
http://s1176.photobucket.com/albums/...3D_DSC7877.jpg

wheelie power in the wet with 3k in the centre!!!!!
"
Its got be an absolute blast to run on turf!!!

Link dose not work.

Read down a bit in the link RJ posted.... its in his thread

Thanks Matt

Tony,

Product is on the site. :)


Also whats the word on the B01i ?

Does anyone know where i could buy the BO1T Buggy engine at, except from Amain and Absolute hobbies that ship overseas. Can't find any stores in Europe that has anygood deal's on this engine:(

Check out the following link : http://www.tecnopower-motor.com/index.php/distributors

Very true,

The B01T is a very interesting engine.
Theres a few shops in Europe that sell them but at 390 EUR (526 USD) for the engine and 475 EUR (640 USD) for the combo set...no thanks. Can't seem to find them cheaper either...
I think a lot of people find this an interesting engine but with those prices not many people will pick them up im afraid.

To compare...you can pick up a Nova +4 team here for 200 EUR (270 USD).

If anybody knows a shop in Europe that sells them cheaper...please post :nod: