2LikesAB Mods Racing Engines
10-06-2009 | 11:29 PM
#61
Tech Regular
Joined: Mar 2009
Posts: 371
From: Allen, TX (another burb of Dallas)
Adam,
I have a modded Picco P7R Evo2 that blew up on me awhile back. I think I was running it was to hot and blew out the rear bearing.
Can I send it to you to look at and see if it is able to be salvaged? The crank and case that is. I think it would need a new P/S/R along with bearings.
If you still have any Picco stuff would you be able to make it an ABModded beast again once you look at it?
Shoot me a PM if you need to, or info of where I could send it.
I have a modded Picco P7R Evo2 that blew up on me awhile back. I think I was running it was to hot and blew out the rear bearing.
Can I send it to you to look at and see if it is able to be salvaged? The crank and case that is. I think it would need a new P/S/R along with bearings.
If you still have any Picco stuff would you be able to make it an ABModded beast again once you look at it?
Shoot me a PM if you need to, or info of where I could send it.
10-06-2009 | 11:57 PM
#62
Hello Mod Man
I have a Max power 3 port .21 buggy racer engine that is just broken in at just under a gallon. It could use more bottom to top and it's a little finiky to tune. It's similar to my nova bf but still slower maybe a little tight. I think it would be a good mod motor. Any feedback would be nice. I saw your website and It seems you do the best work IMO..and others....
10-19-2009 | 07:27 PM
#68
Tech Adept
iTrader: (-1)
Joined: Dec 2007
Posts: 155
I have recieve a gift from Adam today
Look at this beautiful beast!, thank you Adam, can't wait to put it in my X2 CRT.
I've open the engine this after noon, and the cut was so well made that it look like if all was "factory make" on the crank and sleeve.
The threebond sealing job's done by me, not by Adam
Look at this beautiful beast!, thank you Adam, can't wait to put it in my X2 CRT.
I've open the engine this after noon, and the cut was so well made that it look like if all was "factory make" on the crank and sleeve.
The threebond sealing job's done by me, not by Adam
10-20-2009 | 02:24 PM
#69
I too think it is always a good practice to seal up the motor. Mine looks messy to, but effective. I use Lucky 7 so the black is less visible.
But hey, It looks very nice crusin' on the track !!!
Have fun with the new motor !
But hey, It looks very nice crusin' on the track !!!
Have fun with the new motor !
10-20-2009 | 07:06 PM
#70
I have recieve a gift from Adam today
Look at this beautiful beast!, thank you Adam, can't wait to put it in my X2 CRT.
I've open the engine this after noon, and the cut was so well made that it look like if all was "factory make" on the crank and sleeve.
The threebond sealing job's done by me, not by Adam
Look at this beautiful beast!, thank you Adam, can't wait to put it in my X2 CRT.
I've open the engine this after noon, and the cut was so well made that it look like if all was "factory make" on the crank and sleeve.
The threebond sealing job's done by me, not by Adam
10-26-2009 | 08:59 PM
#74
Tech Adept
iTrader: (-1)
Joined: Dec 2007
Posts: 155
I was at the job last week-end and the weather here was realy bad.....SNOW on saturday morning
And my 086 pipe is not here yet. The only pipe i have for now is an RB 9863, don't know if it's the proper ppipe for this engine.
But for break-in , maybe this pipe'll do the job
Anyways, i'll try to start it next week-end if the weather is not to bad
