Team Magic G4
#2971
Hey Mark,
The MF .12MasMo will have a ceramic bearing starting in 2007. Sell yours to one of those guys out there that chase you all and every weekend (lol) and get the new one!
I know your next question ..... will there be a price increase??? ... maybeeee a little one!!!!
Hope your electric season is going well. We will have the new E car for your next series of races!
Have a great Christmas and pass that on to your dad for me also!
Sam
The MF .12MasMo will have a ceramic bearing starting in 2007. Sell yours to one of those guys out there that chase you all and every weekend (lol) and get the new one!
I know your next question ..... will there be a price increase??? ... maybeeee a little one!!!!
Hope your electric season is going well. We will have the new E car for your next series of races!
Have a great Christmas and pass that on to your dad for me also!
Sam
#2972
Originally Posted by Kodak Hodak
ahhh cheers man........ ill check now!
with champ rc drop em an email and they'll get back to you just get the order for and it has there email on it
#2973
anyone modify li-po at g4s,if got let me know how to do,if got picture better lah
#2975
Track Width
I know what your saying about the track width !
My first G4 had this problem and although I haven't yet got my new G4s, I've heard that people were having to wind those pivot balls almost, if not all the way in to get the 200mm tack! : nod:
My first G4 had this problem and although I haven't yet got my new G4s, I've heard that people were having to wind those pivot balls almost, if not all the way in to get the 200mm tack! : nod:
#2976
That should read "TRACK"
#2977
Front Belt protector???
how you think about this protector?
it protect front belt from small rock. ^^;;;;
it protect front belt from small rock. ^^;;;;
#2978
Originally Posted by gansei
how you think about this protector?
it protect front belt from small rock. ^^;;;;
it protect front belt from small rock. ^^;;;;
#2979
Id have to aggree with Serpentd ,id rather leave it open.
#2980
Originally Posted by Serpentd
Dude, not bad. Something to think about though is it might keep rocks from comming out as well. It's sort of damned if you do, damned if you don't scenario. But maybe the ratio of keeping rocks out is higher with your plate that you made. Let us know if you strip less belts with that little guy installed. Hope it works out well! Good luck! Later.
But G4s front bulk cover system is rather complex.. so i think small rock from high position percentage is low.
thanks for your advise.. and if the tip has trouble, i will remove it ^^
#2981
Tech Master
iTrader: (15)
Originally Posted by nitrobeast
Hey
I just noticed that my rear measures 204mm.
I have the rear pivet ball set at factory specs, 4mm spacing from the arm to the hub.
Am i the only one who noticed this? I am measuring it from back of the wheels.
I just noticed that my rear measures 204mm.
I have the rear pivet ball set at factory specs, 4mm spacing from the arm to the hub.
Am i the only one who noticed this? I am measuring it from back of the wheels.
Check the tyres and make sure you haven't got the offset rims. Most manufacturers do an offset rim (required on the MTX) so just check that you have the 0 offset rims.
I run the Jaco tyres and I can adjust the width as I please without having to screw in the pivot balls.
Cheers,
Mike.
#2982
Makes sense ,especially with the Jacos.with 204mm could be you have 2mm offset wheels on your car.
#2983
With the rear balls screwed right in I am at 194mm
But I cant screw the top in enough to get any castor, so I have to unscrew the balls at least 2mm.
But I cant screw the top in enough to get any castor, so I have to unscrew the balls at least 2mm.
#2984
castor? should read camber
#2985
hey guys
do raceday hobbies have a have a shop in the u.s if so where is it located
do raceday hobbies have a have a shop in the u.s if so where is it located