Mugen MTX-3
#1411
Tech Fanatic
DID YOU KNOW?
put the rear body mounts on the other side of the mount the your mtx2 shells will fit!.
#1412
Originally posted by dtm
ic.....I wonder what he was doing with his hands whilst sleeping!!??
ic.....I wonder what he was doing with his hands whilst sleeping!!??
busying with this likely !
#1413
Re: DID YOU KNOW?
Originally posted by Cartman
put the rear body mounts on the other side of the mount the your mtx2 shells will fit!.
put the rear body mounts on the other side of the mount the your mtx2 shells will fit!.
#1414
Tech Fanatic
Originally posted by Manticore
it is not kawahara, but a new brand name "sato seiki". not sure about origin of production
it is not kawahara, but a new brand name "sato seiki". not sure about origin of production
#1415
Tech Elite
iTrader: (52)
Sorry for being late but here she is... (big photo sorry )
Only hop up is the lightweight engine mounts (which trust me weight just about the same as the original ones), MR-12 with slight mods (), 51604 pipe.
With the help of a Dremel, modified the switch/transponder to sit together and lower and mounted the throttle servo below the chassis instead of being on top (this drops it about 8mm and lowers the COG)
Only hop up is the lightweight engine mounts (which trust me weight just about the same as the original ones), MR-12 with slight mods (), 51604 pipe.
With the help of a Dremel, modified the switch/transponder to sit together and lower and mounted the throttle servo below the chassis instead of being on top (this drops it about 8mm and lowers the COG)
#1416
Originally posted by Novarossi
and mounted the throttle servo below the chassis instead of being on top (this drops it about 8mm and lowers the COG)
and mounted the throttle servo below the chassis instead of being on top (this drops it about 8mm and lowers the COG)
#1417
Tech Elite
iTrader: (52)
Originally posted by patelladragger
novarossi - did you have issues with the brake linkage clearing the spur gear when mounting the throttle servo lower like that? I remember mine is very close at the standard mounting position already.
novarossi - did you have issues with the brake linkage clearing the spur gear when mounting the throttle servo lower like that? I remember mine is very close at the standard mounting position already.
You can also mount the brake linkage from the top of the brake lever instead from the bottom
#1418
Originally posted by Novarossi
Have a 48 first gear spur on it and clears it by about 4mm. I've checked it over and over, its fine.
You can also mount the brake linkage from the top of the brake lever instead from the bottom
Have a 48 first gear spur on it and clears it by about 4mm. I've checked it over and over, its fine.
You can also mount the brake linkage from the top of the brake lever instead from the bottom
Anyone else have any building tips (while I've got the thing apart)?
#1419
Tech Regular
For those of you who have run the MTX-3 already, have you guys had any issues with the screws stripping? I finally found some time to build my car (it's been sitting in the box since early November) but haven't run it yet. Everything's perfect right now but I'm concerned that after a few runs, some of these screws will strip the plastic they thread into.
Only reason I'm concerned about this is a friend had a NTC3 which uses similar tight thread screws and everything started stripping after the 4th race or so.. my Serpent had screws with threads that were spaced further apart and these last much longer since there's more plastic between each thread..
Just wondering.
Only reason I'm concerned about this is a friend had a NTC3 which uses similar tight thread screws and everything started stripping after the 4th race or so.. my Serpent had screws with threads that were spaced further apart and these last much longer since there's more plastic between each thread..
Just wondering.
#1420
Originally posted by Cartman
Manti do you have a link?
Manti do you have a link?
#1421
Tech Addict
Originally posted by Novarossi
Have a 48 first gear spur on it and clears it by about 4mm. I've checked it over and over, its fine.
Have a 48 first gear spur on it and clears it by about 4mm. I've checked it over and over, its fine.
Im running the same gearing on 2nd as you and it was awesome
Last edited by David; 12-26-2002 at 10:28 PM.
#1422
to all posting pics... pls post pics no bigger than 640x480, anything bigger causes fourm display issues.
#1423
Black Knight : "none shall pass"
are you the same black knight from Holy Grail ? Hope you still have your arms and legs intact.
Run Away !!!!
Run Away !!!!
#1424
Originally posted by Manticore
busying with this likely !
busying with this likely !
705 in MK now!.....price damn good!!! HK$26xx
#1425
Re: Black Knight : "none shall pass"
Originally posted by Data
are you the same black knight from Holy Grail ? Hope you still have your arms and legs intact.
Run Away !!!!
are you the same black knight from Holy Grail ? Hope you still have your arms and legs intact.
Run Away !!!!