|
1 Attachment(s)
goodies
|
1 Attachment(s)
mid bearing block
|
1 Attachment(s)
snake pipe/wire mount
|
Goodies
Originally posted by Manticore goodies BTW, how do you find the centax ? More like Kawahara ones or Kyosho ones? fly weight is 3 piece or 4 piece? did you use any special tool to install or adjust the centax? great pic... |
Re: Goodies
Originally posted by RClover Manti...what engine is that with a B on the carb? RB? BTW, how do you find the centax ? More like Kawahara ones or Kyosho ones? fly weight is 3 piece or 4 piece? did you use any special tool to install or adjust the centax? great pic... the centax is more like a Mugen Centax :eek: :eek: It is a Mugen ! ;) it has 4 pcs flyweight. I have the spring tension adjusting tool but I merely use it ! |
which one manti ?
looks like i am goin to get a second car already....:p :p :p cant resist the temptation of joining the club....:D
i am comparing MTX-3 with the 705.... cant decide which one to go for... is 705 worth it Manti...??? |
Re: which one manti ?
Originally posted by RClover looks like i am goin to get a second car already....:p :p :p cant resist the temptation of joining the club....:D i am comparing MTX-3 with the 705.... cant decide which one to go for... is 705 worth it Manti...??? |
Re: Re: Goodies
1 Attachment(s)
Originally posted by Manticore the engine is Novarossi S5 but I put on a RB carb on it :smile: :smile: the centax is more like a Mugen Centax :eek: :eek: It is a Mugen ! ;) it has 4 pcs flyweight. I have the spring tension adjusting tool but I merely use it ! spring tension tool? what is this 2 speed clutch tool? |
Re: Re: Re: Goodies
Originally posted by RClover :D :D :D spring tension tool? what is this 2 speed clutch tool? Spring tension tool is to adjust the clutch spring tension. |
Re: Re: which one manti ?
Originally posted by Manticore You asked the wrong person. I am allergic to snake so I am going to tell you a bias comment. You should know what I am going to say dude ! :lol: :lol: |
Re: Re: Re: Re: Goodies
Originally posted by Manticore that one is particular for kyosho 3D clutch. It is for remove/install pinion on the clutch bell. I am not sure if it fits mugen clutch bell. Spring tension tool is to adjust the clutch spring tension. |
Re: Re: Re: which one manti ?
Originally posted by RClover never mind then...:cool: btw, how you rate RR against MTX-3 after testing it out....? |
Re: Re: Re: Re: Re: Goodies
Originally posted by RClover does MTX-3 kit provide this tool? if not, how do you adjust the clutch spring without using your tool? does it difficult to adjust? It is best to use the mugen 2speed tool as this will save you from buying clutch bells. alternative for the clutch spring tension tool is your "fingers" |
Re: Re: Re: Re: which one manti ?
Originally posted by Manticore 2 thumbs up !! :nod: :nod: :nod: :nod: |
Re: Re: Re: Re: Re: which one manti ?
Originally posted by nova racer out the box the mtx 3 is better than the v1rr? |
| All times are GMT -7. It is currently 12:18 PM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.