Mugen MTX-3
#1231
Re: Re: Re: MTX-3 Video
Originally posted by Manticore
it is asphalt. med to high traction
it is asphalt. med to high traction
#1232
Re: Re: Re: Re: MTX-3 Video
Originally posted by RClover
what is the lenght of the str8? 150ft?
what is the lenght of the str8? 150ft?
#1233
Have not started building my MTX3 yet, but i have been reading the instructions etc.... so i have a few questions..
1. Lower Arm Postion, is adjusted using parts T0128 (A,B,C) AND T0129 (A,B,C)...using these parts changes what? am i right in assuming this changes roll center? Also if were to mix and match A,B,C parts i could change the Anti Squat???
2. Has anyone tried different Akerman postions? "A" is the kit pos.
Thanks in advance
Paul
1. Lower Arm Postion, is adjusted using parts T0128 (A,B,C) AND T0129 (A,B,C)...using these parts changes what? am i right in assuming this changes roll center? Also if were to mix and match A,B,C parts i could change the Anti Squat???
2. Has anyone tried different Akerman postions? "A" is the kit pos.
Thanks in advance
Paul
#1234
Tech Adept
Here's My baby.......i have a couple of pics, so bare with me
#1235
Tech Adept
another
#1236
Tech Adept
they just keep coming
#1237
Tech Fanatic
Manti you look like your pushing out the corners, and i like they way in one vid you use another car to turn in!!
someone asked about the mounting of two switches
someone asked about the mounting of two switches
#1238
Originally posted by Cartman
Manti you look like your pushing out the corners, and i like they way in one vid you use another car to turn in!!
someone asked about the mounting of two switches
Manti you look like your pushing out the corners, and i like they way in one vid you use another car to turn in!!
someone asked about the mounting of two switches
#1239
Tech Adept
another
#1240
Tech Adept
some more
#1241
Tech Adept
3 left
#1242
Tech Adept
2 left......and for the servo wires, i bundled them up, and tucked them next to the receiver under the receiver cover.....i then wrapped some tape for security
And in this pic, i am fully aware that my pipe is bent....this happened mid season when my friend in his HPI t-boned me after beating him by a large margin
And in this pic, i am fully aware that my pipe is bent....this happened mid season when my friend in his HPI t-boned me after beating him by a large margin
#1243
Tech Fanatic
Originally posted by eddiethefish
oh! how neat and pretty. Can you guys give me tips on how to hide all those wires. Yours, Manticore and many others did a very good job on it.
oh! how neat and pretty. Can you guys give me tips on how to hide all those wires. Yours, Manticore and many others did a very good job on it.
#1244
Tech Adept
Last but not least.........
oh and i also know my throttle linkage is completely messed up, (missing collars, inverted, servo horn not screwed in completely) but i have a list of things to do before i drive this beast, and it will all be taken care of
oh and i also know my throttle linkage is completely messed up, (missing collars, inverted, servo horn not screwed in completely) but i have a list of things to do before i drive this beast, and it will all be taken care of
#1245
Originally posted by Nytrochaos
2 left......and for the servo wires, i bundled them up, and tucked them next to the receiver under the receiver cover.....i then wrapped some tape for security
And in this pic, i am fully aware that my pipe is bent....this happened mid season when my friend in his HPI t-boned me after beating him by a large margin
2 left......and for the servo wires, i bundled them up, and tucked them next to the receiver under the receiver cover.....i then wrapped some tape for security
And in this pic, i am fully aware that my pipe is bent....this happened mid season when my friend in his HPI t-boned me after beating him by a large margin