Mugen MTX-3
#6046
Originally posted by jiggamacdaddy
where is there a site i can see the engine and who will distribute them?
where is there a site i can see the engine and who will distribute them?
here is the spec.
I believe Trinity is the dealer in USA
#6047
ROBBIE C
i ordered me a complete shock (all 4 set) i find out that the shocks that i got is different than the one i have on my car
is their any way i can call mugen usa and exchange it to the right shock i need
thank
nelly
i ordered me a complete shock (all 4 set) i find out that the shocks that i got is different than the one i have on my car
is their any way i can call mugen usa and exchange it to the right shock i need
thank
nelly
#6048
Tech Master
iTrader: (31)
hi, anyone interested in a brand new never used Alum. brake bracket by SATO racing ? i am only asking $11 shipped to you door ..let me know
[email protected]
[email protected]
#6049
According to Mugen Gear Ratio chart, 17/46 gives a gear ratio of 6.836.
Can somebody please tell me how to calculate this.
Thanks
AL
Can somebody please tell me how to calculate this.
Thanks
AL
#6050
Originally posted by acs
According to Mugen Gear Ratio chart, 17/46 gives a gear ratio of 6.836.
Can somebody please tell me how to calculate this.
Thanks
AL
According to Mugen Gear Ratio chart, 17/46 gives a gear ratio of 6.836.
Can somebody please tell me how to calculate this.
Thanks
AL
#6052
Tech Addict
iTrader: (5)
First race with the MTX-3
I raced my MTX-3 for the first time this weekend and won the thirty minute A-main with 81 laps (2 more than the second place car). The car was box stock and I started with the standard set up. I made a few changes to the set up since the car had a little push off power. This car is a joy to drive, it's very stable and a lot faster in the straight than my MTX-2 was, even though I was still running rich (the temp never went over 205F during hard racing). I can't wait to start playing with different gearing to see how much faster this car can go. At around lap 60 I had to sway left and right to avoid hitting NTC3 parts and dead Serpents laying on the track and clipped a corner pretty hard. I lost a front dogbone but I kept on going. The car was still very fast and nimble. I'm the only one racing Mugen at my club and after the race, a lot of people came under my tent to look at the car, hope to get some of them to convert
#6053
Originally posted by jiggamacdaddy
where is there a site i can see the engine and who will distribute them?
where is there a site i can see the engine and who will distribute them?
#6054
#6055
Front Universal
Any suggestion on which brand of universal joint for Mtx 3 is the best? I already had 2 sets of original Mugen brand universal joint and they broke easily. I ve been looking for the K factory brand but I m not sure if its good. Also I m going to start to put hop up parts to my car, so pls advice me on which part to upgrade first also which brand do make the best hop up for this car.
#6056
Re: First race with the MTX-3
Originally posted by mistercrash
I can't wait to start playing with different gearing to see how much faster this car can go.
I can't wait to start playing with different gearing to see how much faster this car can go.
One thing though, couldn't you just run over the dead snakes?
#6057
Re: Front Universal
Originally posted by dameetz
Any suggestion on which brand of universal joint for Mtx 3 is the best? I already had 2 sets of original Mugen brand universal joint and they broke easily. I ve been looking for the K factory brand but I m not sure if its good. Also I m going to start to put hop up parts to my car, so pls advice me on which part to upgrade first also which brand do make the best hop up for this car.
Any suggestion on which brand of universal joint for Mtx 3 is the best? I already had 2 sets of original Mugen brand universal joint and they broke easily. I ve been looking for the K factory brand but I m not sure if its good. Also I m going to start to put hop up parts to my car, so pls advice me on which part to upgrade first also which brand do make the best hop up for this car.
Manticore uses 3Racing CVD w/ no problem.
MY FRIEND had problem w/ 3Racing and Team Osaka and now stick with Mugen.
You may try 3Racing, but if possible, avoid GPM and K-Factory.
#6058
Where can I buy this 3racing hop up parts? Also I once saw this smaller teeth spur and pinion gear for Mtx 3 but dont know which brand make it and what is the advantage of using this type?
#6059
Originally posted by dameetz
Where can I buy this 3racing hop up parts? Also I once saw this smaller teeth spur and pinion gear for Mtx 3 but dont know which brand make it and what is the advantage of using this type?
Where can I buy this 3racing hop up parts? Also I once saw this smaller teeth spur and pinion gear for Mtx 3 but dont know which brand make it and what is the advantage of using this type?
Keep coming back to this thread, as Manticore and Vinyard will be testing out the 0.8mm gear and will give us the full report.
Manticore and Vinyard, hope I didn't put any burden on your shoulder. Keep writing the report!
#6060
Originally posted by eddiethefish
Justrc.com have it. Those small teeth spur/pinion is the 0.8mm gearing set from Mugen. It's not new; Kawahara has these gear set for years.
Keep coming back to this thread, as Manticore and Vinyard will be testing out the 0.8mm gear and will give us the full report.
Manticore and Vinyard, hope I didn't put any burden on your shoulder. Keep writing the report!
Justrc.com have it. Those small teeth spur/pinion is the 0.8mm gearing set from Mugen. It's not new; Kawahara has these gear set for years.
Keep coming back to this thread, as Manticore and Vinyard will be testing out the 0.8mm gear and will give us the full report.
Manticore and Vinyard, hope I didn't put any burden on your shoulder. Keep writing the report!
i am being thrown into the limelight all of a sudden??
yeah.. hopefully some testing will be done this weekend..