Mugen MTX-4
#6316
Tech Elite
iTrader: (15)
Originally Posted by Corse-R
I can show you the shape of my outdrives after more than 80 litres of fuel (they started on my Xray, then on the MTX3 and now on the MTX4) the shape is great, no visual damage nor wear of the outdrive, at least for me works great.
P.S: I'll post some actual photos of the outdrives on the next days.
P.S: I'll post some actual photos of the outdrives on the next days.
#6317
Originally Posted by JayL
Is this the correct pipe manifold setup for our cars:
http://www.skylinercracing.com/store/P_16.htm
Thanks,
http://www.skylinercracing.com/store/P_16.htm
Thanks,
#6318
Tech Elite
iTrader: (15)
Originally Posted by JayL
Is this the correct pipe manifold setup for our cars:
http://www.skylinercracing.com/store/P_16.htm
Thanks,
http://www.skylinercracing.com/store/P_16.htm
Thanks,
#6319
Originally Posted by Rody
p.s. KidDynomite, I usually run my T2 on ashphalt with rubber tyres, but this was my first ever run on carpet with foams. In the 3rd A final, totally mangled the rear outdrive off the line, and i did not even mash it!!
#6320
Anybody see set-up sheets from the Worlds yet?
Anybody see NEW set-up sheets from anywhere yet?
Anybody see NEW set-up sheets from anywhere yet?
#6321
Originally Posted by THE DOCTOR
Do the outdrives have the hole in the end for the pin that they use for the rear diff?
http://www.teamxray.com/xshop/produc...g%20Steel%20(2)
But I'm using the 'old' ones, weren't lightened so much and were more Nitro suitable. I would scary to death about installing those ones on my MTX4 nowadays.
On the phot I've attached the old outdrives are shown.
Last edited by Corse-R; 10-03-2006 at 02:47 PM. Reason: Missed the photo... I'm turning old. :p
#6322
hmm
just passing through save me some of that track
#6323
Originally Posted by Corse-R
Nope, the ones I'm referring are the one-way outdrives. The new version are those:
http://www.teamxray.com/xshop/produc...g%20Steel%20(2)
But I'm using the 'old' ones, weren't lightened so much and were more Nitro suitable. I would scary to death about installing those ones on my MTX4 nowadays.
On the phot I've attached the old outdrives are shown.
http://www.teamxray.com/xshop/produc...g%20Steel%20(2)
But I'm using the 'old' ones, weren't lightened so much and were more Nitro suitable. I would scary to death about installing those ones on my MTX4 nowadays.
On the phot I've attached the old outdrives are shown.
edit : oops... I get it now..... you were talking only the outdrives.
Last edited by asw7576; 10-04-2006 at 01:31 AM.
#6324
Originally Posted by Nitro$junkie
here are a few pic of my beast
#6325
The spurs are 3racing gears. I know some guys have had problems with them being out of round.
#6327
Originally Posted by tantalus007
am thinking of getting a sirio engine for my mtx4... what modifications would i need to do to my kit??? which engine mount would be better, the alum engine mount from mugen or the one piece engine mount made by kawahara??? tia...
#6329
Originally Posted by AMGRacer
So I am guessing nobody here has tried the Kawahara solid/oneway combo fromn the lack of responses?
#6330
Originally Posted by tantalus007
am thinking of getting a sirio engine for my mtx4... what modifications would i need to do to my kit??? which engine mount would be better, the alum engine mount from mugen or the one piece engine mount made by kawahara??? tia...