Kyosho SuperTen FW-04
#302
No worries, Jon! I didn't bid for it. So it's not necessary anymore.. thanks anyway!
#303
OK finally got the HPI super rubbers installed. I'm using traxxas 12mm hexes for 6mm axle. Nice fit!
My friend spotted these, I think my car came with these having foams on. Wonder what foams were used.
http://www.technicalrp.com/catalog/k...m-p-43333.html
My friend spotted these, I think my car came with these having foams on. Wonder what foams were used.
http://www.technicalrp.com/catalog/k...m-p-43333.html
#304
Still in the middle of the winter but it was above zero C so I took the car out and fired the motor with the old nitro I had left in my garage. It worked pretty well, not perfect but being quite cold I didn't spend so much time tuning it. So at least the motor works rather well and can expect running the stock motor. Plus it was a bit of fun after a long break.
#305
it looks fit nicely, im waiting for that hpi tyres and wheels too from towers,, cant wait.
any report for hpi rubber compound performance?
any report for hpi rubber compound performance?
#306
hi,
did you get the tires ? I think the performance is average, you should be able to run on track fine.
I have not worked on the car even have a few new parts and it waits for the front end rebuild. Just haven't got the time.
I've been tempted to purchase the real 2-speed FZW56 but so far abandonded the idea because of it's price. That would allow me to use the Orion motor that have as spare. The cheaper unit can barely survive the stock GS15R.
If anyone has one to sell, pls PM. Also looking for rear exhaust header and pipe. Not sure if the header I'm waiting from japan to arrive will fit well enough.
did you get the tires ? I think the performance is average, you should be able to run on track fine.
I have not worked on the car even have a few new parts and it waits for the front end rebuild. Just haven't got the time.
I've been tempted to purchase the real 2-speed FZW56 but so far abandonded the idea because of it's price. That would allow me to use the Orion motor that have as spare. The cheaper unit can barely survive the stock GS15R.
If anyone has one to sell, pls PM. Also looking for rear exhaust header and pipe. Not sure if the header I'm waiting from japan to arrive will fit well enough.
#307
Some progress here. Put 50k oil in front diff, shocks 500.
#308
Hi anyone in need of the special edition stock center 2-speed gears and clutchbell have new to spare, also the stock GS15R in good condition with pipe for sale. Willing to trade as well. Let me know cheers!
#309
Hi there super fans!
Got the FZW56 gearbox and I'd love to install the flywheel and pilot shaft on my Orion CRF .12 but unfortunately the dia of the SG shaft is larger.
I don't remember quite well so I need your help to refresh my memory - what parts do you need to install a flywheel and FZW56 clutchbell on it ? Thanks
I also got a new carbon top plate FZW23 but it is for the FW03 I guess since it does not fit the FW04 (should have been FZW52). If anyone is need I'm willing to send it since I have no use for it. If you have clutch parts like the ones above to trade even better.
Thanks again!
Got the FZW56 gearbox and I'd love to install the flywheel and pilot shaft on my Orion CRF .12 but unfortunately the dia of the SG shaft is larger.
I don't remember quite well so I need your help to refresh my memory - what parts do you need to install a flywheel and FZW56 clutchbell on it ? Thanks
I also got a new carbon top plate FZW23 but it is for the FW03 I guess since it does not fit the FW04 (should have been FZW52). If anyone is need I'm willing to send it since I have no use for it. If you have clutch parts like the ones above to trade even better.
Thanks again!
#310
I think I need fzw64 and fzw65 ? Anyone ? thanks!
#311
Hi, a hobby shop japan seems to have these parts avail so I'm trying to get from there. I think these are what I need for a sg/pilot shaft engine to install the fzw56 tranny.
I have some extra parts like the fzw23 carbon deck that i can send if anyone interested as I have no use for it. Cheers
I have some extra parts like the fzw23 carbon deck that i can send if anyone interested as I have no use for it. Cheers
#312
Tech Apprentice
iTrader: (1)
Hi Mika, just saw your post; so you are needing a clutch nut for an Orion .12 SG type shaft, correct? I'm not sure if kyosho made a specific Orion shaft, but if we could get the measurement of the FZW SG type pilot shaft , then we could find another shaft that's made for an Orion .12 that would have the same (or close) length. Shims can be used if the difference is minimal... I'll see what I can come up with
Later man, Jon
Later man, Jon
#313
Tech Apprentice
iTrader: (1)
Hi Mika, just saw your post; so you are needing a clutch nut for an Orion .12 SG type shaft, correct? I'm not sure if kyosho made a specific Orion shaft, but if we could get the measurement of the FZW SG type pilot shaft , then we could find another shaft that's made for an Orion .12 that would have the same (or close) length. Shims can be used if the difference is minimal... I'll see what I can come up with
Later man, Jon
Later man, Jon
#314
Hi Jon, I believe it's pretty much standard measure like the O.S RX-15 so the same parts should fit, no? Is it 6mm dia.
Are your fw03 supers in need of the carbon top plate ? Can send it to you, just pm your address if you like!
Thanks bro!
Are your fw03 supers in need of the carbon top plate ? Can send it to you, just pm your address if you like!
Thanks bro!
#315
Hi guys,, glad to see this thread updated. i got fw03 stock porsche taisan's, very excited. and still dreamin of put all my supertens a FOAM tyre. had no idea how to work it out. since every 1/10 wheels had a smaller diameter and width.
any idea for any supertens fans here,, thx guys.
any idea for any supertens fans here,, thx guys.