R/C Tech Forums

Go Back  R/C Tech Forums > General Forums > Nitro On-Road
Serpent 710 >

Serpent 710

Register
FAQ
Community
Wiki Posts
Calendar
Today's Posts
Search
Vendor Directory

Serpent 710

Thread Tools
 
Search this Thread
 
Old 10-07-2005, 05:40 PM
  #22456  
Tech Initiate
 
Join Date: Mar 2005
Posts: 29
Default
I have the mega picco engine but i got the wrong monoblock whic is for novarossi based. It looks fit.Can that make any problems?
gokhan is offline  
Reply
Old 10-08-2005, 12:37 AM
  #22457  
Tech Elite
 
Sow&Steady's Avatar
 
Join Date: Dec 2003
Location: Va Va Voom!
Posts: 4,104
Default
Originally Posted by gokhan
Thanks dude
Gokhan, hope it was helpful. Did you read Rene's comments below the article? Anyway, follow the instructions and no problems. I would change the rear to a 4 hole to start with.
Sow&Steady is offline  
Reply
Old 10-08-2005, 12:38 AM
  #22458  
Tech Elite
 
Sow&Steady's Avatar
 
Join Date: Dec 2003
Location: Va Va Voom!
Posts: 4,104
Default
Originally Posted by vintage
hi guys, i just got my serpent 710 2 days ago and i got the front diff.....
i need some help putting the front diff together, its a bit diffrent then the read diff that comes with the car
thanks in advance
Do the same as the rear one.
Sow&Steady is offline  
Reply
Old 10-08-2005, 12:39 AM
  #22459  
Tech Elite
 
Sow&Steady's Avatar
 
Join Date: Dec 2003
Location: Va Va Voom!
Posts: 4,104
Default
Originally Posted by sokevin
anyone know where if there is front cva for the 710? part#? i have snap my thread on the dogbone-outdrive when change tire
They are the same.
Sow&Steady is offline  
Reply
Old 10-08-2005, 12:40 AM
  #22460  
Tech Elite
 
Sow&Steady's Avatar
 
Join Date: Dec 2003
Location: Va Va Voom!
Posts: 4,104
Default
Originally Posted by gokhan
I have the mega picco engine but i got the wrong monoblock whic is for novarossi based. It looks fit.Can that make any problems?
If it fits then no problems.
Sow&Steady is offline  
Reply
Old 10-08-2005, 01:44 AM
  #22461  
Tech Initiate
 
Join Date: Mar 2005
Posts: 29
Default
Yep it is ,thanks man also i found another helpful link http://www.mytsn.com/publ/publ.asp?pid=11441..
gokhan is offline  
Reply
Old 10-08-2005, 04:30 AM
  #22462  
Tech Rookie
 
Join Date: Oct 2005
Posts: 5
Default
Originally Posted by Sow&Steady
Do the same as the rear one.
some parts are not the same... the front one comes with 2 clips + no plastic seal or the plastic washer that goes between the sleeve and then diff
vintage is offline  
Reply
Old 10-08-2005, 09:00 AM
  #22463  
Registered User
 
Pyramid's Avatar
 
Join Date: Sep 2001
Location: ID
Posts: 1,945
Default
Originally Posted by gokhan
I have the mega picco engine but i got the wrong monoblock whic is for novarossi based. It looks fit.Can that make any problems?
It looks the same but when you screw them all up, the monoblock will tweak because the width between hole is different.
Pyramid is offline  
Reply
Old 10-09-2005, 07:49 AM
  #22464  
Tech Elite
 
Sow&Steady's Avatar
 
Join Date: Dec 2003
Location: Va Va Voom!
Posts: 4,104
Default
Originally Posted by Pyramid
It looks the same but when you screw them all up, the monoblock will tweak because the width between hole is different.
that's right, it is doesn't fit properly, there is going to be tweak for sure.
Sow&Steady is offline  
Reply
Old 10-09-2005, 11:09 AM
  #22465  
Tech Master
 
Julius's Avatar
 
Join Date: Oct 2003
Location: Amsterdam Netherlands
Posts: 1,063
Default
Originally Posted by gokhan
I have the mega picco engine but i got the wrong monoblock whic is for novarossi based. It looks fit.Can that make any problems?
I'm not 100% sure but I believe the difference is in the placement of the screws that blot the engine to the block. I think in the beginning when we only had the Nova monoblock we drilled out the mounting holes in the engine block slightly to make the Mega fit on the Nova block....

Might be better to try and sell the block at the track or via Ebay and get the correct part...
Julius is offline  
Reply
Old 10-10-2005, 12:17 AM
  #22466  
Tech Regular
 
Join Date: Apr 2005
Posts: 314
Default
Has anyone tried to mount an OS12 TZ to a monoblock? To which one?

Thanks!
fulcrum2 is offline  
Reply
Old 10-10-2005, 12:40 AM
  #22467  
Tech Elite
 
Sow&Steady's Avatar
 
Join Date: Dec 2003
Location: Va Va Voom!
Posts: 4,104
Default
Originally Posted by fulcrum2
Has anyone tried to mount an OS12 TZ to a monoblock? To which one?

Thanks!
I did and it doesn't work. I went back to the stock engine mounts.
Sow&Steady is offline  
Reply
Old 10-10-2005, 04:02 AM
  #22468  
Tech Rookie
 
Join Date: Sep 2005
Posts: 11
Default dogbone pins
Does anyone know the size of the dogbone pins for a serpent 710?
My lhs sells the Hudy replacement pins but I need to know which to take.
hendrikcls is offline  
Reply
Old 10-10-2005, 04:35 AM
  #22469  
Tech Elite
 
Sow&Steady's Avatar
 
Join Date: Dec 2003
Location: Va Va Voom!
Posts: 4,104
Default
Originally Posted by hendrikcls
Does anyone know the size of the dogbone pins for a serpent 710?
My lhs sells the Hudy replacement pins but I need to know which to take.
3 x 9.7mm

BUT take a look at this http://3hobby.net/modules.php?name=E...ontent&tid=168 and click on the link at the bottom of that page.
Sow&Steady is offline  
Reply
Old 10-10-2005, 05:27 AM
  #22470  
Tech Regular
 
Join Date: Apr 2005
Posts: 314
Default
@Sow&Steady

Thanks for your advise!



By the way, Iīve just added a Mugen MRX-4 to my stable of race cars. Does anybody know where I can find a good forum (like this one for the S710) for my new speed machine? Itīs pretty quiet in the Mugen thread here...

Thanks again!
fulcrum2 is offline  
Reply



Advanced Search

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.