Kyosho FW-05R
#1396
Tech Rookie
Can someone help me out with wat 2 get 2 convert to mtx-3 hub?
1. do i need to get different size bearings?
2. do i have 2 change 2 mugen's dog bone & wheel shaft?
3. did i miss out anything?
Thank you very much.
1. do i need to get different size bearings?
2. do i have 2 change 2 mugen's dog bone & wheel shaft?
3. did i miss out anything?
Thank you very much.
#1397
Super Moderator
iTrader: (239)
Re: gears
Originally posted by mikecatts
hi guys,
went to the track today to try a few things...short work day..
39 ring front, 40 ring rear, 22/50 , 29/45.
jp ns3 worlds (not too many of these babies around, i have 2).
kyosho pipe and header..........................
man does this car go.........our rear straight is at least 120metres long wth a sharp 90 degree bend at the end.
this car just keeps pulling........the car is twitchy at high speeds...i think due to trying a new radio as well...ex-10 helios........i blew second gear...on closer inspection i seen that the mesh wasnt 100%...out with the dremel and widened the engine mounting holes...now i got the mesh right...a quick run and no probs....now i need to work on the set-up...ran out of daylight...race day sunday......ill try a few things..
mike
hi guys,
went to the track today to try a few things...short work day..
39 ring front, 40 ring rear, 22/50 , 29/45.
jp ns3 worlds (not too many of these babies around, i have 2).
kyosho pipe and header..........................
man does this car go.........our rear straight is at least 120metres long wth a sharp 90 degree bend at the end.
this car just keeps pulling........the car is twitchy at high speeds...i think due to trying a new radio as well...ex-10 helios........i blew second gear...on closer inspection i seen that the mesh wasnt 100%...out with the dremel and widened the engine mounting holes...now i got the mesh right...a quick run and no probs....now i need to work on the set-up...ran out of daylight...race day sunday......ill try a few things..
mike
#1398
Originally posted by ojo
Can someone help me out with wat 2 get 2 convert to mtx-3 hub?
1. do i need to get different size bearings?
2. do i have 2 change 2 mugen's dog bone & wheel shaft?
3. did i miss out anything?
Thank you very much.
Can someone help me out with wat 2 get 2 convert to mtx-3 hub?
1. do i need to get different size bearings?
2. do i have 2 change 2 mugen's dog bone & wheel shaft?
3. did i miss out anything?
Thank you very much.
Mtx 3 hub (rear upright)
Outer smal bearing ( the inside one is the same size as Kyosho)
Wheel shaft
Pillow balls together with original hex fitter ( the one with black plastic spacer)
Wheel hex
and the spacers at the top of the hub.
You dont need mugen dog bone the kyosho one will fit.
#1399
I have a question on the FW05R does it come with carbon fibre deck shock towers one way etc etc or is all that seperate hop ups?
#1400
Hudy- I think there's a kit that has carbon fibre deck. I'm not sure aobut the one way.... Are you looking at a FW05 now??? I'm still debating.
Last edited by Nitropimp; 05-19-2004 at 10:23 PM.
#1401
Tech Rookie
dameetz,
thanks for d detail listing.
thanks for d detail listing.
#1402
Originally posted by hudy
I have a question on the FW05R does it come with carbon fibre deck shock towers one way etc etc or is all that seperate hop ups?
I have a question on the FW05R does it come with carbon fibre deck shock towers one way etc etc or is all that seperate hop ups?
#1403
marcos
marcos...im using the one way....
Last edited by mikecatts; 08-13-2010 at 02:29 PM.
#1404
nitropimp yes i am currently contemplating about purchasing the FW05R im just not sure if it comes with all the goodies I went to my LHS today and saw it very nice car indeed iys just that jeffreylin confused me even more the one i saw today was in a red box and said it was the FW-05R <Sponge Tire Version> i really did not pay close attention to the numbers
the kit was $334.00
please help is there other version of the fw05r im not aware of i though it was only one please dont flame im a noob at this thx for your help
the kit was $334.00
please help is there other version of the fw05r im not aware of i though it was only one please dont flame im a noob at this thx for your help
#1405
Originally posted by hudy
nitropimp yes i am currently contemplating about purchasing the FW05R im just not sure if it comes with all the goodies I went to my LHS today and saw it very nice car indeed iys just that jeffreylin confused me even more the one i saw today was in a red box and said it was the FW-05R <Sponge Tire Version> i really did not pay close attention to the numbers
the kit was $334.00
please help is there other version of the fw05r im not aware of i though it was only one please dont flame im a noob at this thx for your help
nitropimp yes i am currently contemplating about purchasing the FW05R im just not sure if it comes with all the goodies I went to my LHS today and saw it very nice car indeed iys just that jeffreylin confused me even more the one i saw today was in a red box and said it was the FW-05R <Sponge Tire Version> i really did not pay close attention to the numbers
the kit was $334.00
please help is there other version of the fw05r im not aware of i though it was only one please dont flame im a noob at this thx for your help
#1406
check this site out
hi guys,
check this site for info and prices///
out of japan they call the car "the pro kit".
its got the one way, carbon deck and the upgraded chassis....not bad value..
http://www.rcmart.com/catalog/
check this site for info and prices///
out of japan they call the car "the pro kit".
its got the one way, carbon deck and the upgraded chassis....not bad value..
http://www.rcmart.com/catalog/
#1407
Hudy-what part of California are you from?? This is the post about the kits
31582 kit comes with the carbon fiber top deck, front one-way, lightened chassis, as well as foam tires. 31581A is the rubber tire kit with front diff and regular upper deck and 31581B is the foam tire kit also with front diff and regular upper deck.
#1408
look at this
take a look.
Kyosho (#KY31582) FW-05R Chassis Kit Hop Up edition USD$379.90
Order quantity:
Product 41/42
FW-05R Chassis Kit
1:10 Scale Controlled .12 Engined Powered Touring Car Series
Unaffected by the size of the load placed on it and able to maintain low stress throughout, the 4WD shaft-driven system is now ready for action with full battle racing specs in the PureTen size. Entered as the "R" class in the Kyosho Cup from its inception, and also the JMRCA All Japan National Championships, a new wind is now sweeping through this globally accepted size. Kyosho's long heritage of innovation and development of racing technology have been concentrated in the FW-05 R. With its ultra-low center of gravity, a 3D clutch and 2-speed automatic transmission etc., the FW-05R is ready for racing battle right from its debut! With winning performance as the dominant theme in its design, the new generation 1/10 pure touring machine has arrived!
Newly developed shaft-driven 4WD drive train responds intelligently and lightly when power is put ON or OFF.
Double wishbone suspension with ball-connect system has multiple points of adjustment for a wide scope of settings.
Equipped with high performance components such 3D clutch with shoe mechanism, and a 2-speed transmission at a very competitive price.
Precision 0.8 module gears for minimal loss.
4 bevel gear diff has wide scope for setting selections with different viscosity silicone oils.
Long span suspension arms on both front and rear (longer than V-One).
Design delivers low center of gravity with low-height engine mount and small diameter flywheel etc.
Equipped with center-connect type front stabilizer and piano wire type rear stabilizer.
Direct throttle linkage eliminates any play in throttle control bypassing any relay links.
Many optional upgrade parts designed for the V-One can also be used on the FW-05 R. Body mount positions are also the same as the V-One.
Design allows engine's full power to be extracted through non-restrictive manifold shape.
Globally accepted size can be entered in the JMRCA 1/10 GP Touring Car All Japan Championships among others.
This product was added to our catalog on Wednesday 12 May, 2004
Kyosho (#KY31582) FW-05R Chassis Kit Hop Up edition USD$379.90
Order quantity:
Product 41/42
FW-05R Chassis Kit
1:10 Scale Controlled .12 Engined Powered Touring Car Series
Unaffected by the size of the load placed on it and able to maintain low stress throughout, the 4WD shaft-driven system is now ready for action with full battle racing specs in the PureTen size. Entered as the "R" class in the Kyosho Cup from its inception, and also the JMRCA All Japan National Championships, a new wind is now sweeping through this globally accepted size. Kyosho's long heritage of innovation and development of racing technology have been concentrated in the FW-05 R. With its ultra-low center of gravity, a 3D clutch and 2-speed automatic transmission etc., the FW-05R is ready for racing battle right from its debut! With winning performance as the dominant theme in its design, the new generation 1/10 pure touring machine has arrived!
Newly developed shaft-driven 4WD drive train responds intelligently and lightly when power is put ON or OFF.
Double wishbone suspension with ball-connect system has multiple points of adjustment for a wide scope of settings.
Equipped with high performance components such 3D clutch with shoe mechanism, and a 2-speed transmission at a very competitive price.
Precision 0.8 module gears for minimal loss.
4 bevel gear diff has wide scope for setting selections with different viscosity silicone oils.
Long span suspension arms on both front and rear (longer than V-One).
Design delivers low center of gravity with low-height engine mount and small diameter flywheel etc.
Equipped with center-connect type front stabilizer and piano wire type rear stabilizer.
Direct throttle linkage eliminates any play in throttle control bypassing any relay links.
Many optional upgrade parts designed for the V-One can also be used on the FW-05 R. Body mount positions are also the same as the V-One.
Design allows engine's full power to be extracted through non-restrictive manifold shape.
Globally accepted size can be entered in the JMRCA 1/10 GP Touring Car All Japan Championships among others.
This product was added to our catalog on Wednesday 12 May, 2004
#1409
Originally posted by dameetz
U need the following items:
Mtx 3 hub (rear upright)
Outer smal bearing ( the inside one is the same size as Kyosho)
Wheel shaft
Pillow balls together with original hex fitter ( the one with black plastic spacer)
Wheel hex
and the spacers at the top of the hub.
You dont need mugen dog bone the kyosho one will fit.
U need the following items:
Mtx 3 hub (rear upright)
Outer smal bearing ( the inside one is the same size as Kyosho)
Wheel shaft
Pillow balls together with original hex fitter ( the one with black plastic spacer)
Wheel hex
and the spacers at the top of the hub.
You dont need mugen dog bone the kyosho one will fit.
Thanks
#1410
ziggy,
This should be what you need.
Mugen T0229 F/R axle shaft 1
Mugen T0230 F/r drive shaft 1
Mugen T0139 Rear up right 1
Mugen D0105R king pin 1
Mugen J0110 adjust nut 1
3 Racing mtx3-008 wheel adaptor 1
10 x 15 ball bearing 2
6 x 13 ball bearing 2
This should be what you need.
Mugen T0229 F/R axle shaft 1
Mugen T0230 F/r drive shaft 1
Mugen T0139 Rear up right 1
Mugen D0105R king pin 1
Mugen J0110 adjust nut 1
3 Racing mtx3-008 wheel adaptor 1
10 x 15 ball bearing 2
6 x 13 ball bearing 2