MRX-4X
#318
#319
Spring Rate Chart!
>> FYI <<
Here's one that I've been using for the past few years.
It doesn't have the Yellow's & Pink's but it has the rest /
Mugen Gray, White, Light Blue, Purple, Dark Blue & Red
as well as some other Manufacturers Front & Rear.
Hope this helps!
T
Here's one that I've been using for the past few years.
It doesn't have the Yellow's & Pink's but it has the rest /
Mugen Gray, White, Light Blue, Purple, Dark Blue & Red
as well as some other Manufacturers Front & Rear.
Hope this helps!
T
#320
Mugen message board is now on and live as of 5/23 2008
www.mugenracing.com click on message board create an account and start posting just that easy.
Hopefully this will help people with questions in-regards to setup tips and other frequently asked questions.
www.mugenracing.com click on message board create an account and start posting just that easy.
Hopefully this will help people with questions in-regards to setup tips and other frequently asked questions.
#321
Hey guys I am building my first onroad kit a mrx4x to run at 301 along with my hpi and am new to onroad.I am wondering about the front roll bar setup.I looked at the setup sheet but didn't see any info on tuning it besides rotating the bar.My question is am I suppose to make the roll bars touch eacother when the arms are all the way down, flat or what?Thanks
#324
Tech Adept
#325
Tech Regular
#326
Titanium Rear Spool
we have the titanium rear spool for the MRX4-X now as well.
#327
gidday
can some one shed some light on the mrx-4x clutch set up im new to 1/8 and the clutch set up is diffrent to 1/10
do you just shim the inner bearing so it dosnt drag on the clutch shoe then put the shim in frount of the thrust bearing till you get .3 end play ?that how i read it ,as compeared to a 1/10 were you have a clutch gap then shim the inner bearing till you get the right end play
thanks in advance
can some one shed some light on the mrx-4x clutch set up im new to 1/8 and the clutch set up is diffrent to 1/10
do you just shim the inner bearing so it dosnt drag on the clutch shoe then put the shim in frount of the thrust bearing till you get .3 end play ?that how i read it ,as compeared to a 1/10 were you have a clutch gap then shim the inner bearing till you get the right end play
thanks in advance
#328
gidday
can some one shed some light on the mrx-4x clutch set up im new to 1/8 and the clutch set up is diffrent to 1/10
do you just shim the inner bearing so it dosnt drag on the clutch shoe then put the shim in frount of the thrust bearing till you get .3 end play ?that how i read it ,as compeared to a 1/10 were you have a clutch gap then shim the inner bearing till you get the right end play
thanks in advance
can some one shed some light on the mrx-4x clutch set up im new to 1/8 and the clutch set up is diffrent to 1/10
do you just shim the inner bearing so it dosnt drag on the clutch shoe then put the shim in frount of the thrust bearing till you get .3 end play ?that how i read it ,as compeared to a 1/10 were you have a clutch gap then shim the inner bearing till you get the right end play
thanks in advance
#329
To the best of my memory, Mugen has never said to shim the inside in their instructions though that may have changed with the X. Need to go look at the book. Either way I like to shim the inside so the bell does not rub the shoe. ALWAYS set the endplay FIRST! Then shim the back side to eliminate most of the play.
Oh, and try .4 mm.
Oh, and try .4 mm.
#330
Tech Addict
iTrader: (29)
Hey people,
Anyone know the proper name and place to buy these two products listed below?
1) Roll Bar Handle (silver/chrome color)
2) Rear Wing Mount (body supports) these are the two round pieces that screw into the extreme left/right side of rear body mount. This part do not come in the kit unfortunately.
3) Rear adjustable roll-bar for MRX-4X
Please link any sites that sell them.
I posted a pic and it shows two white rear body supports with flathead screw slots and adj. anti roll-bar
Thanks
Anyone know the proper name and place to buy these two products listed below?
1) Roll Bar Handle (silver/chrome color)
2) Rear Wing Mount (body supports) these are the two round pieces that screw into the extreme left/right side of rear body mount. This part do not come in the kit unfortunately.
3) Rear adjustable roll-bar for MRX-4X
Please link any sites that sell them.
I posted a pic and it shows two white rear body supports with flathead screw slots and adj. anti roll-bar
Thanks