2007 Team Magic G4+ Limited Edition
#227
TM does make the lightweight spool and a lightweight one-way.
These are a huge saving on weight, just where you need it too.......rotational mass!!
K1409 ---- Lightweight front one-way
K1477T --- Lightweight front solid axle
These both need front pulleys to be fitted to them.
K1460 ---- 32t for stock transmission
K14122-9 ---- 30t for ED transmission
Use the duel spool/ one-way to find out which works or you like on the track, then fit the specific lightweight axle to cut down the rotational mass and overaul car weight.
British Menace
#228
#229
#230
2007 European Champion Setup
http://teammagic.com.tw/Download/G4+...2007_setup.pdf
http://teammagic.com.tw/Download/G4+...2007_setup.pdf
Anyone could say what the note on wheelbase means??
front +2/rear -2... Maybe it is 2mm spacers at the rear of the front lower arm and 2mm spacers at the back of the rear lower arms as well?? That would be assuming that the center of the car is the point of reference and then "front +2" means center position +2 mm out to the front??? Would the rear be center position and then moving the rear lower arm 2mm to the front of the car??
Also, is it true Dario did not use the speedshot front bulkhead? I just heard a rumour... Maybe he was saving weight?
From the setup sheet, seems like Dario used the old style rear uprights rather than the newer ones that use aluminum spacers to adjust roll centers...
I do not understand the note on shock pistons...
(1std 1 1.2 mm) I assume it means standard shock piston, 1.2mm holes, but what does the "1" in the middle refer to?? I do not think this is meant to be read "1 standard piston and 1 piston with 1.2mm holes, right??
That looks like very little rear toe-in, doesn´t it?? I realize traction must have been high, but it is still a little surprising!! Obviously it worked!!
It does not list anything on rear camber... or front for that matter...
Thanks!!!
#231
Thanks for the link, Nickko!!
Anyone could say what the note on wheelbase means??
front +2/rear -2... Maybe it is 2mm spacers at the rear of the front lower arm and 2mm spacers at the back of the rear lower arms as well?? That would be assuming that the center of the car is the point of reference and then "front +2" means center position +2 mm out to the front??? Would the rear be center position and then moving the rear lower arm 2mm to the front of the car??
Also, is it true Dario did not use the speedshot front bulkhead? I just heard a rumour... Maybe he was saving weight?
From the setup sheet, seems like Dario used the old style rear uprights rather than the newer ones that use aluminum spacers to adjust roll centers...
I do not understand the note on shock pistons...
(1std 1 1.2 mm) I assume it means standard shock piston, 1.2mm holes, but what does the "1" in the middle refer to?? I do not think this is meant to be read "1 standard piston and 1 piston with 1.2mm holes, right??
That looks like very little rear toe-in, doesn´t it?? I realize traction must have been high, but it is still a little surprising!! Obviously it worked!!
It does not list anything on rear camber... or front for that matter...
Thanks!!!
Anyone could say what the note on wheelbase means??
front +2/rear -2... Maybe it is 2mm spacers at the rear of the front lower arm and 2mm spacers at the back of the rear lower arms as well?? That would be assuming that the center of the car is the point of reference and then "front +2" means center position +2 mm out to the front??? Would the rear be center position and then moving the rear lower arm 2mm to the front of the car??
Also, is it true Dario did not use the speedshot front bulkhead? I just heard a rumour... Maybe he was saving weight?
From the setup sheet, seems like Dario used the old style rear uprights rather than the newer ones that use aluminum spacers to adjust roll centers...
I do not understand the note on shock pistons...
(1std 1 1.2 mm) I assume it means standard shock piston, 1.2mm holes, but what does the "1" in the middle refer to?? I do not think this is meant to be read "1 standard piston and 1 piston with 1.2mm holes, right??
That looks like very little rear toe-in, doesn´t it?? I realize traction must have been high, but it is still a little surprising!! Obviously it worked!!
It does not list anything on rear camber... or front for that matter...
Thanks!!!
this is dario's G4+ after A-main final.
daris used speed front bulk shot.(not aluminum.. But plastic bulk cover)
i quess dario shock piston was 1.0 + 1.2 two hole.. (unbalanced piston setup?)
and.. maybe front wheel base +2 mean normal wheel base of G4S
and rear wheel base was 2mm smaller than G4S.
and i heard from Dario that he always used rear toe-in more than 2.
But he used 1.5 in Euro.. very interesting!!
#232
G4+ Special Edition
For those guys in the U.S who thought all the G4+ Limited Edition cars had gone.............
There is one for sale at
RC Track,
Gaitherburg, MD
Call: 1-301-417-9630
Sale fell through yesterday so it's up for grabs again. I think you'll have to be quick.
Best of luck
British Menace
There is one for sale at
RC Track,
Gaitherburg, MD
Call: 1-301-417-9630
Sale fell through yesterday so it's up for grabs again. I think you'll have to be quick.
Best of luck
British Menace
#233
#234
Darren Johnson and G4+ Finishes in Winning Style
The Final round of the 2007 BRCA 200mm Touring championship took place at the Aldershot circuit, This demanding circuit usually results in some close racing and didn't disappoint.
Saturday practise was run in good conditions, and with the timing computer running, everyone could check the pace of the fastest runners. The usual suspects were all fast, with local drivers Darren Johnson and Stephen Brown at the to of the list.
After qualifying, Darren Johnson took TQ, from Kyle Branson, Ben Cosgrove and Stephen Brown. Darren's time finally managed to beat Mark Green's, very impressive previous track record, as well as 12 second laps for the first time. Darren's new track record of 23 laps in 305.03 left him over five seconds clear of second!
Click on the picture for more detail
The Final round of the 2007 BRCA 200mm Touring championship took place at the Aldershot circuit, This demanding circuit usually results in some close racing and didn't disappoint.
Saturday practise was run in good conditions, and with the timing computer running, everyone could check the pace of the fastest runners. The usual suspects were all fast, with local drivers Darren Johnson and Stephen Brown at the to of the list.
After qualifying, Darren Johnson took TQ, from Kyle Branson, Ben Cosgrove and Stephen Brown. Darren's time finally managed to beat Mark Green's, very impressive previous track record, as well as 12 second laps for the first time. Darren's new track record of 23 laps in 305.03 left him over five seconds clear of second!
Click on the picture for more detail
#235
Congratulations Darren
And also for the Team Magic
And also for the Team Magic
#237
Back again
Hi @ all
Germany is back again with.
After half a Year with MTX4 (very Good Time) il be back again with TM G4+
We will see what we can do!!!!
Marc
Germany is back again with.
After half a Year with MTX4 (very Good Time) il be back again with TM G4+
We will see what we can do!!!!
Marc
#238
Tech Initiate
I have an oppurtunity to get a G4S for quite cheap. Is it worth it? Many of the guys locally are racing Xrays and Mugens. I wanted to be a little different plus the deal I am getting is pretty sweet.
Thanks
Thanks
#239
Will there be a G4+ upgrade kit for the G4S?Cheers...
#240
there are no G4+ conversion kit.
But you can do G4+ conversion by several parts
<FRONT>
*502286 G4+ Front Lower Flying Wing Arm (1 pair)........
*502292 G4+ Front Upper Flying Wing Arm (1 pair).........
<REAR>
*502288 G4+ Rear Bulkhead ..............................
*502196-1 G4+ Back Bracket (Plus).........................
*502291 G4+ Rear Lower Flying Wing Arm (1 pair) ........
*502287 G4+ Flying Wing Arm Clip and Spacer Set (2) ....
*K14134 G4+ 3x60.5mm Hinge Pin .........................
*K14131 G4+ New Carbon Brake Bracket ...................
*K14130 G4+ Alum. Rear Anti-Roll Bar Mounts (w/anti-roll bar)...
*K14123-7 G4 Flash-Pit System Set.............
(k14123-7 seperate parts)
-K14123-1 G4+ Flash-Pit System Insert..........
-K14123-2 G4+ Steering Block (L & R)..........
-K14123-3 G4+ Rear Hub Carrier (L & R)........
-K14123-4 G4+ Rear Upper Link Set.............
But you can do G4+ conversion by several parts
<FRONT>
*502286 G4+ Front Lower Flying Wing Arm (1 pair)........
*502292 G4+ Front Upper Flying Wing Arm (1 pair).........
<REAR>
*502288 G4+ Rear Bulkhead ..............................
*502196-1 G4+ Back Bracket (Plus).........................
*502291 G4+ Rear Lower Flying Wing Arm (1 pair) ........
*502287 G4+ Flying Wing Arm Clip and Spacer Set (2) ....
*K14134 G4+ 3x60.5mm Hinge Pin .........................
*K14131 G4+ New Carbon Brake Bracket ...................
*K14130 G4+ Alum. Rear Anti-Roll Bar Mounts (w/anti-roll bar)...
*K14123-7 G4 Flash-Pit System Set.............
(k14123-7 seperate parts)
-K14123-1 G4+ Flash-Pit System Insert..........
-K14123-2 G4+ Steering Block (L & R)..........
-K14123-3 G4+ Rear Hub Carrier (L & R)........
-K14123-4 G4+ Rear Upper Link Set.............