Go Back  R/C Tech Forums > General Forums > Nitro Off-Road
8T 2.0 Setup sheets....post here >

8T 2.0 Setup sheets....post here

8T 2.0 Setup sheets....post here

Old 07-13-2009, 01:44 PM
  #1  
Tech Master
Thread Starter
iTrader: (5)
 
jzemaxx's Avatar
 
Join Date: Jan 2008
Location: North Alabama
Posts: 1,586
Trader Rating: 5 (100%+)
Default 8T 2.0 Setup sheets....post here

Ride Height

Front = stock
Rear =stock

Droop

Front = -5mm from stock
Rear= stock

Sway Bars

Front = stock
Rear = stock

Springs/Shock oil/Pistons

Front = Stock/Stock/stock
Rear = Purple/ 40wt/stock




Diffs

Front Diff =7
Rear Diff =2
Center-diff=10

Gearing


Gearing = 17/50



A-arms/Toe/Camber/Hubs

Front = stock/stock/stock/middle
Rear = stock/ 3-3 plate/stock/middle


Tire and Wheels

Aka = Ibeams soft
Proline- Calibers soft



Chassis & body

chasis = stock
body = stock

Electronics/Battery and Battery Placement

steering Servos = jr8711
Throttle/Brake servo = N/A
Battery = Zippy Flightmax's
Electronics = CC MMM

Engine/Pipe/Plug/Fuel

motor = NEU 1515 1Y
Pipe =
Plugs =
Fuel =

Track Conditions- Loose,dry, sandy and loamy
jzemaxx is offline  
Old 07-13-2009, 03:00 PM
  #2  
Tech Master
iTrader: (4)
 
reggie l.'s Avatar
 
Join Date: Jan 2009
Location: randallstown md.
Posts: 1,360
Trader Rating: 4 (100%+)
Default

Ride Height

Front = bones below level
Rear = bones above level


Droop

Front =
Rear=


Sway Bars

Front = 2.3
Rear = 2.3

Springs/Shock oil/Pistons

Front = black/35/56
Rear = grey/ 30wt/56




Diffs


Front Diff = 7
Rear Diff = 2
Center-diff=smart/grease

Gearing/flywheel


Clutch=m2c
Clutchbell/spur gearing =[/b] 13/50
flywheel= i run both steel some times and alum


A-arms/Toe/Camber

Front =
Rear =


Tire and Wheels
aka's-proline caliber


Chassis & body


chasis = stock
body = stock

Electronics/Battery and Battery Placement

stering Servos = futuba bl351
Throttle/Brake servo = futuba bl451
Battery = losi lipo 2000
Electronics = spec

Engine/Pipe/Plug/Fuel

motor =ninja jx21-vspec as a back up
Pipe = assotiated
Plugs = os
Fuel = byrons gen2 30%

i need to go home and mesure stuff...i will edit later
reggie l. is offline  
Old 07-13-2009, 03:25 PM
  #3  
Tech Champion
iTrader: (25)
 
losi_racer's Avatar
 
Join Date: Nov 2008
Location: mesa,az
Posts: 6,470
Trader Rating: 25 (100%+)
Default

Ride Height

Front = 39
Rear =42

Droop

Front =110(tryin 105 next time)
Rear= 130

Sway Bars

Front = 2.3
Rear = 2.3(going to 2.0)

Springs/Shock oil/Pistons

Front = Black/55/35
Rear = grey/56/32.5




Diffs

Front Diff =7
Rear Diff =2
Center-diff=10

Gearing


Gearing = 13/50



A-arms/Toe/Camber/Hubs

Front = stock/stock/ -1 /foward
Rear = stock/ stock/ -2 / foward


Tire and Wheels
Front- crimefighter m3
Rear- Bow-ties M3
(going to caliper m3)


Chassis & body

chasis = stock
body = jconcept

Electronics/Battery and Battery Placement

steering Servos = hobbico
Throttle/Brake servo = jr 4800
Battery =nimh 1600


Engine/Pipe/Plug/Fuel

engine = Vspec
Pipe = ae 2035
Plugs = p3
Fuel =sidewinder(going torco)

Track Conditions- hard packed/high bite
losi_racer is offline  
Old 07-13-2009, 05:50 PM
  #4  
Tech Champion
iTrader: (17)
 
JAMMINKRAZY's Avatar
 
Join Date: Jun 2007
Location: Pittsburgh PA
Posts: 6,575
Trader Rating: 17 (100%+)
Default

I'll just modify Reggie's because I am lazy.

Ride Height

Front = 39mm
Rear = 42mm


Droop

Front = 110mm
Rear= 130mm


Sway Bars

Front = 2.3
Rear = 2.0

Springs/Shock oil/Pistons/positions

Front = black/35wt/55/Middle on arm, middle on tower
Rear = grey/ 30wt/56/Middle on arm, Outer on tower


Diffs


Front Diff = 7
Rear Diff = 3
Center-diff= 10

Gearing/flywheel


Clutch= Fioroni Turbo Twin 2007 w/ 2 hard springs
Clutchbell/spur gearing= 13/50
flywheel= fioroni


Toe/Antisquat

Front = 2* Out
Rear = 3/3

Losi adjustable toe blocks. Running all 0's in the front block set. 1's up in the forward rear block, 0's in the back rear block.

Camber

Front = -1
Rear = -2

Tire and Wheels
AKA, Proline, J-concepts, Panther, Losi, etc..(AKA Cityblocks #1)


Chassis & body


chasis = stock
body = stock
Wing = stock

Electronics/Battery and Battery Placement

stering Servo = Hitec 5955TG
Throttle/Brake servo = futuba bl451
Battery = Stickman 2500mah 5 cell AA pack
Electronics = Dx3r & DSM2 reciever, AMB PT

Engine/Pipe/Plug/Fuel

motor = v-spec
Pipe = Losi RE11
Plugs = OS P3
Fuel = Odonnell 20% race

Camber Links, Hubs

front = Middle on tower, Aluminum carriers with one shim below the link.
rear = Lower on tower, innner on hub
hubs = Middle

107mm front camber links in the rear to achieve my settings.

Ackerman
Short

Track Conditions. Hard pack, medium bite.

Last edited by JAMMINKRAZY; 07-15-2009 at 12:35 PM.
JAMMINKRAZY is offline  
Old 07-13-2009, 09:13 PM
  #5  
Tech Master
iTrader: (4)
 
reggie l.'s Avatar
 
Join Date: Jan 2009
Location: randallstown md.
Posts: 1,360
Trader Rating: 4 (100%+)
Default

i need to try the 2.0 sway bar in the rear... i see a coupe ppl run it
reggie l. is offline  
Old 07-13-2009, 09:26 PM
  #6  
Tech Champion
iTrader: (17)
 
JAMMINKRAZY's Avatar
 
Join Date: Jun 2007
Location: Pittsburgh PA
Posts: 6,575
Trader Rating: 17 (100%+)
Default

Originally Posted by reggie l. View Post
i need to try the 2.0 sway bar in the rear... i see a coupe ppl run it
the 2.0 bar and shorter rear links are tips posted by Casey Peck in the 8T 2.0 thread. I made both changes for this past weekend, and noticed a big increase in turn in. It reduced on power steering a tad, but I can deal with that.
JAMMINKRAZY is offline  
Old 07-13-2009, 09:42 PM
  #7  
Tech Master
iTrader: (4)
 
reggie l.'s Avatar
 
Join Date: Jan 2009
Location: randallstown md.
Posts: 1,360
Trader Rating: 4 (100%+)
Default

Originally Posted by JAMMINKRAZY View Post
the 2.0 bar and shorter rear links are tips posted by Casey Peck in the 8T 2.0 thread. I made both changes for this past weekend, and noticed a big increase in turn in. It reduced on power steering a tad, but I can deal with that.
kool i will def try that..
reggie l. is offline  
Old 07-14-2009, 04:08 AM
  #8  
TIX
Tech Master
iTrader: (17)
 
TIX's Avatar
 
Join Date: May 2008
Location: Melbourne Australia
Posts: 1,958
Trader Rating: 17 (100%+)
Default

Ride Height

Front = 39mm
Rear = 42mm


Droop

Front = 110mm
Rear= 130mm


Sway Bars

Front = 2.3mm
Rear = 2.3mm

Springs/Shock oil/Pistons/Location

Front = black / 35wt / 55 / Middle on tower & Middle on arm
Rear = white / 32.5wt / 56 / Out on tower & Middle on arm




Diffs


Front Diff = 7k
Rear Diff = 3k
Center-diff= 10k

Gearing/flywheel


Clutch= on my RB C6 i use a Losi Steel flywheel, 2 carbon with green springs 2 MaxLife with gold springs. on my RB WS7 i use a Losi aluminium flywheel, 2 carbon with gold springs 2 MaxLife with silver springs
Clutchbell/spur gearing= 13/50


Toe/Antisquat

Front = 2* Out
Rear = 3.25/3

Losi adjustable toe blocks. Running all 0's in the front block set. 1's up in the forward rear block, .5's out in the back rear block.

Camber

Front = -2
Rear = -3

Tire and Wheels
AKA's, Losi/GRP's and Prolines with GRP foams


Chassis, body and wing


chasis = stock
body = stock
wing = Team Associated RC8

Electronics/Battery and Battery Placement

stering Servo = Hitec 7955TG
Throttle/Brake servo = Hitec 7955TG
Battery = 1600mah hump pack
Electronics = Nomadio React

Engine/Pipe/Plug/Fuel

motor = RB C6BBT L2G / RB WS7III L2G
Pipe = RB 2045
Plugs = Odonnell 99T
Fuel = NitroX HB7333

Camber Links, Hubs

front = 2 / A
rear = 3 / B
hubs = all the way forward


Track Conditions. Hard pack, large jumps, various bite
TIX is offline  
Old 07-14-2009, 08:22 AM
  #9  
Tech Elite
 
Join Date: Mar 2009
Location: Aurora, Colorado
Posts: 4,026
Default

Ride Height

Front = 38mm
Rear = 42mm

Droop

Front = -110mm
Rear= 130mm

Sway Bars

Front = 2.3mm
Rear = 2.3mm

Springs/Shock oil/Pistons

Front = Black/40wt/55
Rear = Grey/ 32.5wt/56
FULL REBOUND

Diffs

Front Diff =10
Rear Diff =5
Center-diff=10

Gearing

Gearing = 13/50

A-arms/Toe/Camber/Hubs

Front = stock/stock/stock/middle
Rear = stock/ 3-3 plate/stock/middle

Tire and Wheels

Aka = Ibeams med
Proline- Calibers med - FREAKIN GREAT the best tire out
Proline - BowTies hard

Chassis & body

chasis = stock
body = stock / upgrade RC

Electronics/Battery and Battery Placement

steering Servos = JR 9100T
Throttle/Brake servo = JR 9100S
Battery = Losi Lipo
Electronics = AMB

Engine/Pipe/Plug/Fuel

motor = OS Vspec - Ninja JX - Nova +4 - OS 28
Pipe = 2060 - 2060 - Nova - JP3
Plugs = OS P3
Fuel = Byrons Gen 3 30%

Track Conditions- Loose,dry, loamy, no water
token is offline  
Old 07-15-2009, 12:21 PM
  #10  
Tech Master
iTrader: (54)
 
Join Date: Apr 2006
Posts: 1,592
Trader Rating: 54 (100%+)
Default

Ride Height

Front = 37mm
Rear = 39mm


Droop

Front = 108mm
Rear= 128mm


Sway Bars

Front = 2.3mm
Rear = 2.3mm outdoor / 2.5mm indoor


Springs/Shock oil/Pistons/Location

Front = black / 35wt / 55 / Middle on tower & Middle on arm
Rear = Mugen 10.5 / 32.5wt / 56 / Out on tower & Middle on arm



Diffs


Front Diff = 7k
Rear Diff = 4k
Center-diff= 20k

Gearing/flywheel


Clutch= Mugen 3 shoe w/1.0 springs
Clutchbell/spur gearing= 13/50


Toe/Antisquat

Front = 2* Out
Rear = 2.5* outdoors, 2.0* indoors / 3*

Rear toe blocks are stock in front and Losi adjustable in the rear.

Camber

Front = -2
Rear = -2

Tire and Wheels
CityBlock, City/Beam, Raptors


Chassis, body and wing


chasis = stock
body = stock
wing = stock

Electronics/Battery and Battery Placement

stering Servo = Hitec 7955TG
Throttle/Brake servo = Futaba BLS451
Battery = 2000mah lipo
Electronics = KO Propo EX-1 / Specktrum

Engine/Pipe/Plug/Fuel

motor = Ninja JX21
Pipe = JP3
Plugs = P3
Fuel = NitroJuice

Camber Links, Hubs

front = 2 / A
rear = 3 / B
hubs = all the way forward


Track Conditions. Outdoor: Big, open, hard pack, Dusty. Indoor: Hard pack, medium to good traction, tight

Edit: Forgot, short Ackerman
jsmax is offline  
Old 08-04-2009, 11:30 PM
  #11  
Tech Master
iTrader: (4)
 
reggie l.'s Avatar
 
Join Date: Jan 2009
Location: randallstown md.
Posts: 1,360
Trader Rating: 4 (100%+)
Default

Originally Posted by JAMMINKRAZY View Post
the 2.0 bar and shorter rear links are tips posted by Casey Peck in the 8T 2.0 thread. I made both changes for this past weekend, and noticed a big increase in turn in. It reduced on power steering a tad, but I can deal with that.
kan you post pics? of this
reggie l. is offline  
Old 08-04-2009, 11:35 PM
  #12  
Tech Master
iTrader: (4)
 
reggie l.'s Avatar
 
Join Date: Jan 2009
Location: randallstown md.
Posts: 1,360
Trader Rating: 4 (100%+)
Default

EDITED

Ride Height

Front = bones below level
Rear = slightly above level


Droop

Front = 109(just to make sure it doesnt extend to much over 110)
Rear=129(same as the front)


Sway Bars

Front = 2.3
Rear = 2.3

Springs/Shock oil/Pistons

Front = black/35/56
Rear = grey/ 30wt/56




Diffs


Front Diff = 7k
Rear Diff = 2k
Center-diff=10k

Gearing/flywheel


Clutch=m2c...answer r/c
Clutchbell/spur gearing =[/b] 13/50
flywheel= i run both steel some times and alum


A-arms/Toe/Camber

Front =2 out
Rear =


Tire and Wheels
aka's-losi xtt's


Chassis & body


chasis = stock
body = stock

Electronics/Battery and Battery Placement

stering Servos = futuba bl351
Throttle/Brake servo = futuba bl451
Battery = losi lipo 2000
Electronics = spec

Engine/Pipe/Plug/Fuel

motor =ninja jx21-vspec as a back up
Pipe = re11
Plugs = os
Fuel = byrons gen2 30%
reggie l. is offline  
Old 08-05-2009, 12:07 AM
  #13  
Tech Champion
iTrader: (17)
 
JAMMINKRAZY's Avatar
 
Join Date: Jun 2007
Location: Pittsburgh PA
Posts: 6,575
Trader Rating: 17 (100%+)
Default

Originally Posted by reggie l. View Post
kan you post pics? of this
Not really much to see in a picture. Just shorter camber links running in the inner most hole.
JAMMINKRAZY is offline  
Old 08-05-2009, 06:06 AM
  #14  
Tech Master
iTrader: (4)
 
reggie l.'s Avatar
 
Join Date: Jan 2009
Location: randallstown md.
Posts: 1,360
Trader Rating: 4 (100%+)
Default

Originally Posted by JAMMINKRAZY View Post
Not really much to see in a picture. Just shorter camber links running in the inner most hole.
lets say im a visual learner
reggie l. is offline  
Old 08-05-2009, 11:46 AM
  #15  
Tech Champion
iTrader: (17)
 
JAMMINKRAZY's Avatar
 
Join Date: Jun 2007
Location: Pittsburgh PA
Posts: 6,575
Trader Rating: 17 (100%+)
Default

Originally Posted by reggie l. View Post
lets say im a visual learner
Dude seriously, it's just shorter rear links. Run the #1 hole on the tower(lower hole) and hole A on the hubs(inner hole).
JAMMINKRAZY is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.