CEN Matrix TR
#424
Tech Initiate
Hey guys,
Just wanted to say after reading all that i could from this site and some others, I have decided to sale off all of my Jammin's and move over to CEN.
I get of my both my kits tomorrow. hopefully i can get 1 of them built to race this weekend.
I am curious if i can use some extra Jammin parts that i have, Can i use the 17 mm wheel hubs? if so can i use the same wheels with the standard Jammin off set?
Thank's for all of the helpfull information.
Just wanted to say after reading all that i could from this site and some others, I have decided to sale off all of my Jammin's and move over to CEN.
I get of my both my kits tomorrow. hopefully i can get 1 of them built to race this weekend.
I am curious if i can use some extra Jammin parts that i have, Can i use the 17 mm wheel hubs? if so can i use the same wheels with the standard Jammin off set?
Thank's for all of the helpfull information.
#425
Tech Master
The 17mm hubs won't fit. Get the Matrix or Mugen ones. Yes you can use the same wheels & Tires.
The center diff will fit right in and the servo saver. Everything else is different.
The center diff will fit right in and the servo saver. Everything else is different.
#427
Tech Master
Jammin hubs use a 2.5mm pin, CEN uses a 3mm pin - they won't fit.
#428
Tech Initiate
Originally Posted by Machine's R/C H
Jammin hubs use a 2.5mm pin, CEN uses a 3mm pin - they won't fit.
#430
rreg: thanks for the setup info
#431
Tech Champion
iTrader: (4)
lockmouth.. i notice new avatar....
nice setup of the TR.
i actually in the middle of forcing our LHS here to bring in the Arena TR so that i buy from them. Im not sure ordering from USA can save me cost. I can't wait to try all of the recommended setups and mods by u all.
geez... keep this thread alive. the next time i come here, i probably posted a new TR picture
nice setup of the TR.
i actually in the middle of forcing our LHS here to bring in the Arena TR so that i buy from them. Im not sure ordering from USA can save me cost. I can't wait to try all of the recommended setups and mods by u all.
geez... keep this thread alive. the next time i come here, i probably posted a new TR picture
#432
Tech Adept
iTrader: (3)
well not sure if anyone else tried this but when i used to have my TR i used the Matrix "Buggy" rear Axles so there wasn't as many "Shims" and used Thunder Tiger hubs to use 17mm rims...but i heard of a few using the Mugen ones? i never seen them?? but understood they worked well.....
#433
Tech Master
iTrader: (33)
Originally Posted by jfc_tech
lockmouth.. i notice new avatar....
nice setup of the TR.
i actually in the middle of forcing our LHS here to bring in the Arena TR so that i buy from them. Im not sure ordering from USA can save me cost. I can't wait to try all of the recommended setups and mods by u all.
geez... keep this thread alive. the next time i come here, i probably posted a new TR picture
nice setup of the TR.
i actually in the middle of forcing our LHS here to bring in the Arena TR so that i buy from them. Im not sure ordering from USA can save me cost. I can't wait to try all of the recommended setups and mods by u all.
geez... keep this thread alive. the next time i come here, i probably posted a new TR picture
My only sponsor is my back pocket
I hope someday to pick up a sponsor ,but I need to improve on my driving
#434
Tech Master
iTrader: (33)
Oh.. geeze you guys caught me.. I did drill them out and put a 3mm drill blank in the pins place.. blank was only around 2$ through mcmaster.
Your machine buddy can probly help with that..
Sorry.. i missed that large step .. but all in all I was out with 17mm hubs for around 15 after shipping and about 30mins of work...
Your machine buddy can probly help with that..
Sorry.. i missed that large step .. but all in all I was out with 17mm hubs for around 15 after shipping and about 30mins of work...