2010 MMR Electric Challenge April 9th,10th,11th
01-05-2010, 10:52 AM
#1
2010 MMR Electric Challenge April 9th,10th,11th
Well Time is finally here.
Here are the dates for the 4th Annuel MMR Electric Challenge.
48 x 80 CRC Fast Track carpet , CRC Click Link track barriers. No Wintergreen compounds, Gripper, traction action, Sticky fingers all good to use.
Drivers Layout, Expect some turns and rolling corners, carousels & chicanes.
Classes:
VTA MMR Spec, 3.7v 17.5
WGT MMR Spec, 3.7v 13.5 Body TBA
1/12th Stock 3.7v 17.5
1/12th Mod 3.7v open motor
Stock Sedan 17.5
SS Sedan 13.5
MMR VintageTrans-Am Club Spec Rules and Specifications
Body Specifications:
Body provided deck lid spoilers allowed (not wings). No additional skirts or raised/extended wings or air control surfaces allowed. Body must be trimmed
at body trim lines. Full rear bumper required.
Tire & Wheel Specifications:
HPI tire part #4793 front and #4797 rear, stock tire inserts provided with tire and any HPI Vintage wheels designed to fit.
26mm width fronts and 31mm width rear tires. 8-spoke Vintage wheels from #3805 through #3814, 5-spoke Vintage wheels from #3815 through #3822 and Vintage stock car
wheels from #3854 through #3860 are all legal wheels.
Grinding of tire tread is NOT permitted. Sanding of mold seam to remove seam is allowed.
Tires must have visible tread.
Chassis Specification:
Four Wheel Drive touring car chassis only. Tires must fit within the body.
Motor Specifications:
Option 1: 27-turn ROAR stock motor: ROAR motor rules apply for 27 turn.
Option 2: 17.5 brushless motor: ROAR Motor Rules for 17.5
Battery Specifications:
3-cell NiCd or NiMh batteries
1-cell LiPo hard cased
Ride Height Specification:
Minimum ride height is 5mm.
Weight Specification:
Minimum 1280g Lipo
Race Specification:
5 minute Qualifiers Heats are run “heads up” with horn starts. Shuffling of start order for each round with slowest qualifier first and fastest qualifier last
9 Minute Mains: Starting grid should have cars aligned at angles along a side wall of the track.
Body List:
HPI part numbers:
17510 - 1970 Plymouth AAR 'Cuda
17519 - 1966 Ford Mustang GT
17508 - 1965 Ford Shelby GT-350
7494 - 1968 Chevrolet Camaro
17526- 1969 Chevrolet Corvette
Parma part numbers:
10143 - 1969 Z28 Camaro
10141 - 1970 Boss Mustang
10113 - 1970 'Cuda
Pegasus Hobbies part numbers:
PGH4001 - 1970 Camaro SS
PGH4002 - 1970 'Cuda
PGH4003 - 1970 Mustang
2009 http://www.rctech.net/forum/minnesot...4-25-26-a.html
2008 http://www.rctech.net/forum/minnesot...19th-20th.html
2007 http://www.rctech.net/forum/minnesot...allenge-2.html
Here are the dates for the 4th Annuel MMR Electric Challenge.
48 x 80 CRC Fast Track carpet , CRC Click Link track barriers. No Wintergreen compounds, Gripper, traction action, Sticky fingers all good to use.
Drivers Layout, Expect some turns and rolling corners, carousels & chicanes.
Classes:
VTA MMR Spec, 3.7v 17.5
WGT MMR Spec, 3.7v 13.5 Body TBA
1/12th Stock 3.7v 17.5
1/12th Mod 3.7v open motor
Stock Sedan 17.5
SS Sedan 13.5
MMR VintageTrans-Am Club Spec Rules and Specifications
Body Specifications:
Body provided deck lid spoilers allowed (not wings). No additional skirts or raised/extended wings or air control surfaces allowed. Body must be trimmed
at body trim lines. Full rear bumper required.
Tire & Wheel Specifications:
HPI tire part #4793 front and #4797 rear, stock tire inserts provided with tire and any HPI Vintage wheels designed to fit.
26mm width fronts and 31mm width rear tires. 8-spoke Vintage wheels from #3805 through #3814, 5-spoke Vintage wheels from #3815 through #3822 and Vintage stock car
wheels from #3854 through #3860 are all legal wheels.
Grinding of tire tread is NOT permitted. Sanding of mold seam to remove seam is allowed.
Tires must have visible tread.
Chassis Specification:
Four Wheel Drive touring car chassis only. Tires must fit within the body.
Motor Specifications:
Option 1: 27-turn ROAR stock motor: ROAR motor rules apply for 27 turn.
Option 2: 17.5 brushless motor: ROAR Motor Rules for 17.5
Battery Specifications:
3-cell NiCd or NiMh batteries
1-cell LiPo hard cased
Ride Height Specification:
Minimum ride height is 5mm.
Weight Specification:
Minimum 1280g Lipo
Race Specification:
5 minute Qualifiers Heats are run “heads up” with horn starts. Shuffling of start order for each round with slowest qualifier first and fastest qualifier last
9 Minute Mains: Starting grid should have cars aligned at angles along a side wall of the track.
Body List:
HPI part numbers:
17510 - 1970 Plymouth AAR 'Cuda
17519 - 1966 Ford Mustang GT
17508 - 1965 Ford Shelby GT-350
7494 - 1968 Chevrolet Camaro
17526- 1969 Chevrolet Corvette
Parma part numbers:
10143 - 1969 Z28 Camaro
10141 - 1970 Boss Mustang
10113 - 1970 'Cuda
Pegasus Hobbies part numbers:
PGH4001 - 1970 Camaro SS
PGH4002 - 1970 'Cuda
PGH4003 - 1970 Mustang
2009 http://www.rctech.net/forum/minnesot...4-25-26-a.html
2008 http://www.rctech.net/forum/minnesot...19th-20th.html
2007 http://www.rctech.net/forum/minnesot...allenge-2.html
01-18-2010, 06:46 AM
#2
Starting to get entry confirmations in.
The list is here. http://jlapracemanager.com/PC/Molzer...%20Listing.HTM
The list is here. http://jlapracemanager.com/PC/Molzer...%20Listing.HTM
03-07-2010, 06:46 PM
#4
Remember the 15th is the cut off for early reduced entry fees.
Must be paid in the shop or postmarked by the 15th.
Also we will purchase trophies for classes based on preentries at that point. Some classes have had less participation and we are ordering top 3 and tq awards for all classes with 5 or more entries. if the count goes over 5 for a class at the event the trophies will be mailed.
Must be paid in the shop or postmarked by the 15th.
Also we will purchase trophies for classes based on preentries at that point. Some classes have had less participation and we are ordering top 3 and tq awards for all classes with 5 or more entries. if the count goes over 5 for a class at the event the trophies will be mailed.
03-08-2010, 10:00 PM
#5
VTA
1/12 stock
1/12 mod
Stock sedan
Jess Isakson
Spectrum & personal's
1/12 stock
1/12 mod
Stock sedan
Jess Isakson
Spectrum & personal's
03-09-2010, 06:16 AM
#6
Is early entry discount $5 off total or each class?
03-09-2010, 10:34 AM
#8
OK, that's great.
I'm in for mod12th and SS sedan.
I'm in for mod12th and SS sedan.
03-09-2010, 12:50 PM
#9
VTA.
DSM. Loaner, I'm poor.
DSM. Loaner, I'm poor.
03-18-2010, 08:26 AM
#11
Rules Clarification
I see on the flyer you are planning on making everyone run a specific body for the WGT class. I have heard from 2 different people on this matter.
1 person says yes you are doing this and 1 says no you aren't doing this. So I thought I had better come directly to the source.
1. Is this going to happen?
2. If I show up with a different body, will I be allowed to run?
1 person says yes you are doing this and 1 says no you aren't doing this. So I thought I had better come directly to the source.
1. Is this going to happen?
2. If I show up with a different body, will I be allowed to run?
03-19-2010, 03:08 PM
#12
Suspended
Is it really necessary for one race track to have 7 active threads going at one time.
03-22-2010, 05:48 AM
#14
Couple quick clarifacations on wgt for this event only:
tire will be open to the spec tires from jaco, bsr, or crc and any wgt body. You may not mix tire brands. Ie front and rear tires must be from same manufacturer.
Sorry for not being more clear early on the wgt rules for the challenge.
tire will be open to the spec tires from jaco, bsr, or crc and any wgt body. You may not mix tire brands. Ie front and rear tires must be from same manufacturer.
Sorry for not being more clear early on the wgt rules for the challenge.
03-25-2010, 04:33 AM
#15
Just a few short weeks away.... Jacket carriers will be turning in jackets at the end of the chal... Series champions will be crowned and perminently added to the jackets. 2010 chall winners will e added to the wall... Lots of gret racing and great friends... How fun looks like we will have Jari, Mitch, Randy all in house at the same time can we keep up???? Or can they 
trophies are ordered.... Only a few things left to put Ito place...
trophies are ordered.... Only a few things left to put Ito place...