R/C Tech Forums - View Profile: Milkdudd
R/C Tech Forums

Go Back  R/C Tech Forums > Members List
Reload this Page >

Milkdudd's Profile

Register
FAQ
Community
Wiki Posts
Calendar
Today's Posts
Search
Vendor Directory

Milkdudd Milkdudd is offline

Tech Master

Last Activity: 04-25-2024 11:35 AM

About Me

  • About Milkdudd
    Biography
    Was into racing off-road electric from the early 1980s to the early 1990s. Mostly with the MORE Club in and around Metro Detroit. Flew ( mostly crashed) RC planes for a couple of years.
    Location
    Southeast Michigan
    Interests
    Anything that gets my 60 plus year old carcass off of the couch
    Country of Residence
    US
    Gender
    Male

Statistics

Total Posts
General Information
  • Last Activity: 04-25-2024 11:35 AM
  • Join Date: 08-15-2019
  • Referrals: 0

Likes Given

400 Likes
  1. Milkdudd liked post by lbckevin On thread : Tlr22-4 worth picking up
    Get the new 22x4 buggy. You wont regret it. Much easier maint and servicing.
    Liked On: 04-06-2020, 10:21 PM
    Posted On: 04-06-2020, 09:21 PM
  2. Milkdudd liked post by billjacobs On thread : Tlr22-4 worth picking up
    I have the 22-4, eb410.2 (upgraded from original), d418 and xb4. The 22-4 is a fantastic jumper in 13.5, but it is not as fast as the modern shaft cars. It is also heavier, stiffer, and is not a...
    Liked On: 04-06-2020, 10:21 PM
    Posted On: 04-06-2020, 05:52 PM
  3. Milkdudd liked post by Funkydrummer1 On thread : Tlr22-4 worth picking up
    So in my opinion the 2.0 would be my choice. What Ive found is a lot of the 1st gen ebs are pretty beat up. You can still find nice ones of course. The nice thing about Tekno is its very competitive...
    Liked On: 04-06-2020, 10:20 PM
    Posted On: 04-06-2020, 05:09 PM
  4. Milkdudd liked post by fantomdude On thread : Tlr22-4 worth picking up
    If money is not an issue always go with the newer version. That is the version that will get all the support now. If you are on a budget and love to race then save the 100 bucks so you can still...
    Liked On: 04-06-2020, 02:19 PM
    Posted On: 04-06-2020, 02:15 PM
  5. Milkdudd liked post by xlgraphicspro On thread : Tekno EB410.2 Thread
    depends on what it is. It might be a possibility.
    Liked On: 04-05-2020, 10:35 PM
    Posted On: 04-05-2020, 11:28 AM
  6. Milkdudd liked post by Davidka On thread : Rear mounted 2wd
    Unless my memory fails me, I believe you even have the option to do the 4-gear standup transmission, which should be the best for truly low grip conditions.
    Liked On: 04-01-2020, 09:47 AM
    Posted On: 04-01-2020, 07:15 AM
  7. Milkdudd liked post by Will27 On thread : Yokomo YZ-2
    If you have the old style 3 gear laydown, you will need the motor plate also Z2-304T. And decide what rear shocks you want to run. If you want to stick with the standard DTM shocks check your shock...
    Liked On: 03-31-2020, 10:08 PM
    Posted On: 03-31-2020, 08:50 PM
  8. Milkdudd liked post by Cain On thread : Yokomo YZ-2
    just an FYI I have seen a guy have his battery fly out using just the single screw to the chassis side rail. In general the 2 screw method is what I would recommend with the stock mounts personally....
    Liked On: 03-31-2020, 10:04 AM
    Posted On: 03-31-2020, 08:10 AM
  9. Milkdudd liked post by Will27 On thread : Yokomo YZ-2
    Because the holder is lower, there is less leverage over the side rail so it can't flex as much and the edge of the side rail keeps the holder straight. There is a little bit of wriggle, but I...
    Liked On: 03-30-2020, 12:59 AM
    Posted On: 03-29-2020, 10:21 PM
  10. Milkdudd liked post by RogerM On thread : Team Associated B6.1 & B6.1D thread
    Here is what I wrote in the B6.2 thread, same applies for the B6.1. https://www.rctech.net/forum/showpost.php?p=15611782&postcount=675 Hope that helps :)
    Liked On: 03-29-2020, 10:19 PM
    Posted On: 03-25-2020, 06:35 AM
  11. Milkdudd liked post by Fred Perkins On thread : Yokomo YZ-2
    Just don't use the holes. You will be fine
    Liked On: 03-20-2020, 11:02 AM
    Posted On: 03-19-2020, 06:56 PM
  12. Milkdudd liked post by Cain On thread : Yokomo YZ-2
    you will either want to drill then, or just order the chassis that is drilled for the tranny
    Liked On: 03-20-2020, 11:02 AM
    Posted On: 03-20-2020, 07:43 AM
  13. Milkdudd liked post by mushroomed On thread : Team Associated T6.1
    Yes that’s correct, and the manual hasn’t been updated. You can use the stroke length from the setup sheet in the manual (the stroke is printed wrong in the build step only). For the kit setup...
    Liked On: 03-17-2020, 01:12 AM
    Posted On: 03-17-2020, 12:23 AM
  14. Milkdudd liked post by Maxxican On thread : Surpass V4S Motors
    Well, gave this motor another try on saturday practice day. still can't get this dialed in i've never had issues with any other motors like this. it will be going for sale tonight on here. V4s...
    Liked On: 03-14-2020, 06:41 AM
    Posted On: 09-09-2019, 09:30 AM
  15. Milkdudd liked post by Cain On thread : Yokomo YZ-2T 2WD ST truck
    Sounds good, looking forward to hearing how it goes for you.
    Liked On: 03-11-2020, 09:21 AM
    Posted On: 03-11-2020, 07:26 AM
Page 25 of 27
« First
15
23
24
25
26
27

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.