INI nih pembalap RC juga Race real race car!
http://www.teammagic.com.tw/en/newsf...20101808-98837

di Indo siapa yah?

Mar. 20, 2007 - Gil Losi, Jr., an icon in the RC business and co-founder of Team Losi™, is coming to Kyosho America. Beginning in April, Losi will join the Kyosho America team as R&D Director in an effort to better align Kyosho products with the US market.


Nah loh ntar nama mobil nya jadi merk Kyo-Lo atau KYOSHI? (kyosho- Loshi)
moga2 baut2 ukuran tetep metric size gak ke Inch /US standard

hahaha...hari minggu malam saya k PIM..but udh gak ada tuh body mini z....
yg ada kit rtr nya aja...hehehehe....

hihihi....paling bt memang pake produk us...om erwin...
hhehehe...musti beli kunci2 inchi nya..males...

iya emang dah abis, sisa yang overland aja ....
waktu itu cuma ada 2 body, yg nismo diambil erry n yang F360 diambil yudha ... hik3x...

mungkin di MultiToys laen masih ada ga yah ?

STC senayan
 

Gimana nasib track STC senayan... forum sepi nih.. :cry:

Oh gitu yah ..jadi ga bisa nge gossip gitu toh? :lol:

ada yang pernah nyoba mini x??
 

MINI X

Four wheel drive, four wheel independent suspension
*Front and Rear Ball Differental
*Front Caster, Front and Rear Camber, Front toe-in adjustable
*Chassis balance adjustable
*Floating steering bar
*Low center of gravity designed
*4pcs.-6pcs. AAA battery (4.8V-7.2V)
*Independent mini servo, ESC, receiver
*Well fitted with most 1/24 scale model car body
*Good performance on different surfaces

MINI X REVIEW
 

Introduction:
What is this? A 4WD 1:24th scale! However, I suppose that it is the first time for you to hear about the co-existence of these two words. 4WD is widely employed nowadays in 1:10th scale or any bigger scale model car. Without a doubt, 1:24th scale is the hottest topic in R/C field since the introduction of the Kyosho(r) Mini-Z(tm). Therefore, at this time, we will put our sight to focus on this new dominance The Mini-X(tm)!

Overview:

Basically, Mini-X(tm) is categorized into the same class of mini car like the Mini-Z(tm). Obviously, you figured that out from its way cool name Mini-X(tm). However, it does not have a single part from our well-known Mini-Z(tm). If the mini car is a 1:24th scale class category. Then, Sun Sun Model(r) just upped the ante, the Mini-X(tm) is the new benchmark of the 1:24th scale car and it brings this class category to a new level of fun.

Build and Construction:

The Mini-X(tm) is not gas engine power and it will not fly with wings. However, there is no exaggeration that Mini-X(tm) is an innovated mini car with the concept in mind from their Xpress(tm) 1:10th scale model. For its appearance, it is generally the same as a normally 1:10th scale R/C car, but in a 1:24th scale - Plastic chassis, antenna tube and four slick/tread striptires. After removing the plastic chassis, you will find that it is really a great design. All parts are assembled with great care and detail. Four independent suspension arms, slick tires or tread strip tires. The motor is positioned in the center for good balance front and rear. Also, features a front and rear ball differential gear, camber adjustment, 4 AAA battery compartment, floating steering bar, strong mini-servo, power ESC and long distance RF 27MHz radio.
The provided motor is a 70 (Turns) and comes with a long shaft to link the front and rear gear. The generic ball differential design is similar to all 1:10th scale up, but it is tiny! They are made of 8 (2mm diameter) steel differential balls sandwiched between 2 steel plates and 8 (1.5mm diameter) small pressure balls for the compensation of tightness balancing. Motor and gear (8 pitches) combination is simple and clear because it is direct drive motor to the gear of ball differential (select 34, 35 and 36 pitches) in both front and rear. Very simple and direct layout. Optional one-way ball differential will be available. 4 wheel Independent suspension system: Four points designed with rod bar compensation. The dog-bone transmission allows the free moment of each suspension unit. The degree of hardness of each unit can be adjusted by different combination of spring set. Just like the bigger cars! There are two sub-functions from the front of suspension system which are the degree of camber and 2 cluster modes exchange. A 2 cluster mode coarse tuning effects the response of the steering, allowing a wider steering angle. Believe it or not Mini-X(tm) can make 60cm circles.
All electronics are optionally included. The Radio Receiver is using the standard amplitude modulation at 27 MHz frequency band. There are two channels - steering servo and ESC. The receiving range is up at around 50 ft or 15m. The receiver is able to suppress the unexpected bad signal influence and result from the purpose of protection. The Mini-X(tm) can have a wide operating range from 4.8V to 7.2V and the maximum current is 10A. It is programmable to calibrate with different model of AM Radio system. The calibration procedures are full throttle, full brake and Neutral" and it is performed by the assistance of both LEDs indication and Single touch control. The size of battery should be any AAA type. Mini-X is capable to be powered by 4 batteries or 6 batteries. Currently there are two soft plastic chassis available. They are similar to Toyota supra and Toyota corolla. Therefore, racer can design your own patterns with different paint and provided sticker. Another great feature of Mini-X(tm) is most 1:24th scale model cars can fit with minor modifications. Let your imagination go wild!

Review and Test Drive:
Basically, Mini-X is very different from any mini R/C cars available in the market. The independent suspension system replaces the popular H-plate design to assist the steering condition. Firmness can be achieved by adjusting the hardness of spring instead of hardness of H-plate offering a higher amount of variables in track conditions. The Independent suspension design helps the mini-X run in most surfaces with good performance. No ride height rings are necessary. The height of car body can be adjusted by simply adjusting the screw at the bottom piece of suspension arm. With the integration with front and rear ball differential system, maximum traction of 4WD becomes possible. The front suspension system is not only responsible for its basic function of independent suspension, but the degree of camber and cluster can be adjusted in a very neat way. These two sub-functions can combine to make a wider range of steering response. The center of gravity of the car set is relatively lower than any mini-cars. This can be obvious found from the placement of battery, motor, ESC and Receiver. The factory ESC is powerful enough to drive a wider range of motor without damage. The strong and reliable radio foundation allows Mini-X to be played in any areas.

In other words, Mini-X can run in a high speed in a wider condition.

sudah liat di toko jason...berat bener weight nya...hueuheuheue....

oh yah? hm, tapi ada yang pernah maenin gak? apa lebih stabil? handlingnya gimana? disana dijual brapa? kalo liat website, harganya lebih murah jauh dari mini Z

kalo gak salah body mini-X terbuat dari polycarbonet ya??? kayak body RC 1/10......... Mini-Z kan bodinya solid plastik bisa di cat ulang

kalo diliat websitenya bodynya lexan, betul gak bisa dicat ulang, tapi body mini x harganya disana cuman USD 2.50 nah dibanding body mini Z khan jauh banget harganya

kalo diliat websitenya bodynya lexan, betul gak bisa dicat ulang, tapi body mini x harganya disana cuman USD 2.50 nah dibanding body mini Z khan jauh banget harganya

Ada lagi neh yang disebut mini z clone