HK Talk Version 1.1
#5116
Originally posted by Manticore
sure no problem !
sure no problem !
#5117
Originally posted by dtm
hehe... no no...I will run the engine box stock first to get a datum before doing anything to it!! But it does appear to have obvious areas for improvement!
hehe... no no...I will run the engine box stock first to get a datum before doing anything to it!! But it does appear to have obvious areas for improvement!
#5118
Originally posted by Manticore
all my NR variation engines lock up after initial run in and the lock up disappear after at least 1/2 gallon of fuel. My MT12 didnt have this symptom.
all my NR variation engines lock up after initial run in and the lock up disappear after at least 1/2 gallon of fuel. My MT12 didnt have this symptom.
#5119
Originally posted by Manticore
I have "improved" my 5 port already. It screams !
I have "improved" my 5 port already. It screams !
#5120
Originally posted by dtm
haha..... 5 ports..... front one way.... rear straight shaft......... 5...4...3...2...1.... READY FOR LAUNCH!!!!!
haha..... 5 ports..... front one way.... rear straight shaft......... 5...4...3...2...1.... READY FOR LAUNCH!!!!!
#5121
Originally posted by Manticore
i might need to run my 5 port at egr otherwise it is pointless
i might need to run my 5 port at egr otherwise it is pointless
#5122
Originally posted by KY9fat
I'm also changing back to stock screws too.. the take-off screws are too hard and I have ripped a thread on one of my MT case Also for the "Mei Come" the 4 screws there are not quite 2.6mm. its slightly larger and we have been fitting 2.6mm scres!!
I'm also changing back to stock screws too.. the take-off screws are too hard and I have ripped a thread on one of my MT case Also for the "Mei Come" the 4 screws there are not quite 2.6mm. its slightly larger and we have been fitting 2.6mm scres!!
#5123
Originally posted by dtm
You are too heavy handed!!! Just think of all that force you are putting on those poor 2.6mm screws!!!!!
You are too heavy handed!!! Just think of all that force you are putting on those poor 2.6mm screws!!!!!
#5124
Originally posted by dtm
5 port vs RS.... when??? when????
5 port vs RS.... when??? when????
#5126
Originally posted by Disaster999
nono...im just saying that the mspeed screws wont strip and its perfect fit!
nono...im just saying that the mspeed screws wont strip and its perfect fit!
#5127
Regional Moderator
iTrader: (1)
Originally posted by dtm
My MT was a real b!tch when it was new (and so were the other guys too!) I remember having to remove the engine off the car a couple of times to unlock it!!!!! The XT and RS was a lot smoother.... maybe I have a 'duff' engine???!!!!!!
My MT was a real b!tch when it was new (and so were the other guys too!) I remember having to remove the engine off the car a couple of times to unlock it!!!!! The XT and RS was a lot smoother.... maybe I have a 'duff' engine???!!!!!!
#5128
Regional Moderator
iTrader: (1)
Originally posted by Manticore
i am tellng you the secret of speed !!
i am tellng you the secret of speed !!
i rather get some MANTICORE stickers!!...i would be kicking serious arse if i have those sticks....except manticore's arse...hehehe!!
#5129
Originally posted by Disaster999
you know what.....i dont really car about NR or waigo stickers because they suck!!1
i rather get some MANTICORE stickers!!...i would be kicking serious arse if i have those sticks....except manticore's arse...hehehe!!
you know what.....i dont really car about NR or waigo stickers because they suck!!1
i rather get some MANTICORE stickers!!...i would be kicking serious arse if i have those sticks....except manticore's arse...hehehe!!
#5130
Originally posted by Manticore
i mean PYC is too small for the 5 port !
i mean PYC is too small for the 5 port !