Team Associated F1
#334
Tech Prophet
iTrader: (9)
Join Date: Nov 2014
Location: Far south suburbs of Chicago area
Posts: 17,634
Trader Rating: 9 (100%+)
Basic assembly complete. Have to get steering lined up. And fill shock. I'll be ordering motor/ESC in about another week. Still a month or more till group starts running.
Build took much longer then expected. Guide wasn't well done. Maybe to those with experience with this style they might have been clear. But this style is new to me.
Build took much longer then expected. Guide wasn't well done. Maybe to those with experience with this style they might have been clear. But this style is new to me.
#335
Tech Prophet
iTrader: (9)
Join Date: Nov 2014
Location: Far south suburbs of Chicago area
Posts: 17,634
Trader Rating: 9 (100%+)
#336
Tech Addict
iTrader: (41)
Generally have never had a problem building any kit in the past 20 years, but this thing has me stumped. Has anyone else had an issue with the front suspension build step four. When I assembled it, the servo mounts are too high, and not in contact with the chassis and they also don't line up with the holes in the chassis.
As you can see from the photos I have the top plate just resting on the car because the holes don't line up anywhere. I'm not sure if the front bulkhead is too tall, or the standoffs are too short. Also either the chassis holes are wrong or the servo top plate is wrong because none of that lines up. Please someone teel me I'm wrong because I rather it be my mistake then have to deal with finding out what parts are wrong and chasing them down through AE.
As you can see from the photos I have the top plate just resting on the car because the holes don't line up anywhere. I'm not sure if the front bulkhead is too tall, or the standoffs are too short. Also either the chassis holes are wrong or the servo top plate is wrong because none of that lines up. Please someone teel me I'm wrong because I rather it be my mistake then have to deal with finding out what parts are wrong and chasing them down through AE.
#337
You slide the servo carbon piece forward and down, then screw it down. The bulkhead slots in the two holes.
#338
Tech Prophet
iTrader: (9)
Join Date: Nov 2014
Location: Far south suburbs of Chicago area
Posts: 17,634
Trader Rating: 9 (100%+)
#340
#341
#343
Mine is almost done.
I'm going to run for the first time at 360 raceway tonight.
I also found few fitting issue on the front suspension, somebody needs to make that ball outta Aluminium IMO. until then I filed them down then polished them. moving well now.
Few tips I can share while I'm doing that is, I pulled out my old trick to popped the balls in and out easily without damage them. as shown above
Also, even though it shared same part # there is 2 different part as shown bottom of the pic
And that manual!!
Question: how do you achieve 3.8mm RH in the rear? mine seating at 4.2 with -1mm Rear ball bearing housing. maybe because of the brand new tire?
Happy Motoring!
Last edited by J Lee; 04-19-2017 at 07:45 AM.
#344
Good luck John Lee at 360v2 tonight... Traction roll...lol....
My 3racing fgx is ready for the battle this summer....
See you soon....
My 3racing fgx is ready for the battle this summer....
See you soon....
Last edited by bertrandsv87; 04-19-2017 at 05:54 PM.
#345
Tech Prophet
iTrader: (9)
Join Date: Nov 2014
Location: Far south suburbs of Chicago area
Posts: 17,634
Trader Rating: 9 (100%+)
Basic assembly complete. Got few things to get adjusted. Still deciding on color and order motor/esc.
https://youtu.be/wstTJep2SMk
https://youtu.be/wstTJep2SMk